manualshive.com logo in svg

BLAUBERG VENTO Eco, Руководство по эксплуатации, Страница: 16 / 20

Поделиться
Скачать
BLAUBERG VENTO Eco Скачать руководство пользователя страница 16

16

www.blaubergventilatoren.de

VENTO Eco / VENTO Eco2

POSSIBLE REASONS AND TROUBLESHOOTING

Problem

Possible reasons

Troubleshooting

The fan does not start up 

during the unit start-up. 

The control panel displays 

no information and does 

not respond to the button 

pressing.

No power supply.

Make sure the power supply line is connected 

correctly, otherwise troubleshoot the 

connection error.

The control panel displays an 

alarm indicator 

.

Motor is jammed, the impeller blades are 

clogged.

Turn the unit off. Clean the impeller to 

troubleshoot the motor jam. Restart the unit.

Communication loss in connecting cable 

between the fan motor and the control panel.

Turn the unit off. 

Contact the Seller for further information.

Automatic switch tripping 

following the unit turning on.

Overcurrent as a result of short circuit in the 

electric line.

Turn the unit off. 

Contact the Seller for further information.

Low air flow.

Low set fan speed.

Set higher speed.

The filters, the fan or the regenerator are 

clogged.

Clean or replace the filter. Clean the fan and the 

heat exchanger.

Noise, vibration.

The impeller is clogged.

Clean the impeller.

Store the unit in the manufacturer’s original packing box in a dry ventilated premise at ambient temperatures from +5 ˚C ( 41 ˚F) up to 

+40 ˚C (104 ˚F).

Storage environment must not contain aggressive vapours and chemical mixtures provoking corrosion, insulation and sealing deformation.

Use suitable hoist machinery for handling and storage operations to prevent possible damage to the unit.

Follow the handling requirements applicable for the particular type of cargo.

The unit can be carried in the original packing by any mode of transport provided proper protection against precipitation and mechanical 

damage.

Avoid sharp blows, scratches or rough handling during loading and unloading.

Do not expose the unit to sudden changes in temperature.

Such changes can lead to condensation of moisture inside the unit and performance disturbance when the unit is switched on.

Prior to the initial power-up after transportation at subzero temperatures allow the unit to warm up at room temperature for at least 

2 hours.

TROUBLESHOOTING

STORAGE AND TRANSPORTATION REGULATIONS

Содержание VENTO Eco





















Отзывы:

Нет отзывов