Blast DEFIANT 2 Скачать руководство пользователя страница 6

Страница: 6 / 14

defiant

TIIO

IIN

C o m p e t i t i o n

L o c k

B o a r d O p e r a t i o n

MODE SELECTION

(Version 127.4T FRENZY only)

The LED FRENZY Board is driven via the Two-Button Membrane Pad on the rear of the Trigger Frame
(figure “A”) as well as the On-Board Dip Switch Panel (figure “B”) located on the front side of the Fenzy
Board and is accessed by removing the left trigger frame panel. Dip Switches 1 and 2 control DEBOUNCE,
Dip Switch 3 controls CAPPED MODE, Dip Switch 4 controls FIRING MODE, and Dip Switches 5 and 6 control
DWELL. Below are descriptions of the different modes and how they affect the Marker’s performance.

EYE

- Upon Powering up, the

DEFIANT 2’s

ACE System will always default to

FORCED MODE

. Pressing

Button 1 will Deactivate the ACE System and the marker will resume operation utilizing the
currrently selected Firing Mode, in

DRY FIRE MODE.

Pressing Button 2 will change the current

ACE System Setting to

DELAY MODE

. Listed below are descriptions of each ACE System Setting.

FORCED

- Marker fires only when ball is present at time of trigger pull.

DELAY

- Marker fires when ball is present at time of trigger pull and if a ball IS NOT

present the Marker will wait 1 second before firing.

DRY FIRE

- ACE System is Bypassed (OFF) and Marker fires at time of trigger pull.

DEBOUNCE

- Determines (in milli seconds) how long after each trigger pull, the board will ignore

further trigger activity.

(see figure “C” for details)

CAPPED MODE

- Determines if marker operates at an unlimited rate of fire or under a 15bps Cap.

FIRING MODE

- Determines which Firing Mode is selected.

(see figure “C” for details)

DWELL

- Determines how long the bolt remains in the forward position before repeating cycle.

Changing Dip Switch Settings is very simple.

Sliding Switches UP sets them to the

position,

while Sliding Switches DOWN sets them to the

OFF

position. A small paper clip works well for

toggling Dip Switches. The chart below illustrates how the Dip Switch Panel affects the settings.

indicates DOWN, while

indicates UP.

COMPETITION LOCK

- With Competition Lock

, Dwell and Debounce settings are locked and

cannot be changed until Competition Lock is

DISABLED

. While in Competition Mode the Eye Sensor

setting can be changed as normal to Dry Fire Mode or Delay Mode. When Competition Lock is
active, the LED will aluminate Green as normal upon powering up.

(Marker is not BPS capped

while using competition Lock)

ACTIVATING COMPETITION LOCK:

1. Turn Marker OFF.
2. Open up Trigger Frame to gain access to the Circuit Board.
3. Short out

and

Terminals (holes) at the top of the board.

Paper clips work well for this. Bend the clip so that one
end is touching the

and the other end is touching

4. Turn Marker ON.
5. Turn Marker OFF.
6. Disconnect the

and

short and leave off

for at least 30 seconds.

7. Reassemble Trigger Frame.
8. Ready to use with COMPETITION LOCK.

To turn OFF Competition Lock follow the same procedure.
When Competition Lock is active the marker will only operate
in Semi-Auto Mode and Ramping Mode will be disabled.

For information and instructions regarding previous and/or
future versions of the FRENZY Board (Other than version 127.4T),
please refer to separate instructions sheet included in box.

Turn Marker OFF

Membrane Pad

Open Trigger Frame

Disconnect Short, Leave OFF

Reassemble Trigger Frame

COMPETITION LOCK

Short out C and D Terminals

Turn ON

Comp Lock ON

Turn OFF

Terminals

C D