Blanco BFD9XP, Инструкция по эксплуатации

Страница: 6 / 16

11
EN
10
EN
5/ DETERGENT PRODUCTS AND ADJUSTING THE WATER SOFTENER
Important :
The multi-purpose products setting enables you to deactivate the rinsing and salt warning
lights only on
H0
and “Multi-purpose products”.
• Loading the multi-purpose tablet dispenser
To assist in loading the detergent, the distributor is situated on the front of the upper basket. It is
compatible with all the products recommended for dishwashers.
• Place the tablet
in the external compartment (Fig 04 on previous page) or, for optimum
results, pull out the distributor’s drawer and lay the tablet inside (Fig 05 on previous page).
- Close the dispenser.
• FOR MULTI-PURPOSE PRODUCTS (
Water hardness less than at 25°F)
• Your appliance automatically adapts to using multipurpose products when
the water hardness is less than 25°F.
5/ DETERGENT PRODUCTS AND ADJUSTING THE WATER SOFTENER
Important:
It is very important to set the water softener correctly.
- If the setting is too low, there is the risk of chalky marks appearing.
- if the setting is too high, there is the risk of causing clouding of the glasses.
If you relocate, adjust the water softener setting as required.
• Standard washing tablets
Non-multipurpose tablets should be placed in the external compartment (Fig 04) or, for optimum
performance, pull out the dispenser drawer and lay the tablet inside (Fig 05).
• Powders or liquids (Fig 13)
Fill at least up to the minimum mark for slightly dirty crockery and to the maximum mark for dirty
crockery. If the crockery is very dirty and for programmes with a pre-wash we recommend that you
add 5g of detergent (a dessert spoonful) into your dishwasher’s tub in accordance with the pro-
grammes table.
Important:
Keep these products out of children’s reach and away from dampness.
Only use products specially designed for dishwashers.
Fig. 04 Fig. 05 Fig. 03
• FOR STANDARD WASHING PRODUCTS
• Your machine must be specially adjusted to use standards washing products.
• Proceed as follows to adjust the water softener on the control panel:
— This feature is adjusted using the “S
ET
” ; button; hold
down this button to access the menu. Then press twice to
set the softener level.
— The softener level is then shown on the screen from
H H0 0
to
H H6 6
. The default level is
H H4 4
..
— To change the level from
H H0 0
to
H H6 6
, depending on the water hardness, press either arrow button
several times the screen displays the level you have set.
— The setting is validated automatically after 10 seconds if the “ S
ET
” button in not pressed again.
— Pressing “S
ET
” enables you to validate the setting and move on to the next parameter.
T Te essttiin ng g ssttrriip p
H Ha arrd dn ne es ss s 0-10°F 10-18°F 18-25°F 25-40°F 40-55°F 55-70°F > 70°F
T Trra ad diittiio on na all
p prro od du uc ctt
HI H0 H2 H3 H4 H5 H6
45°C 70°C 65°C 55°C 45°C
T Te es sttiin ng g s sttrriip p
H Ha arrd dn ne es ss s 0-10°F 10-18°F 18-25°F
M Mu ullttii--p pu urrp po os se e
pprroodduuccttss FFuunnccttiioonn DDeeaaccttiivvaatteedd
M Mu ullttii--p pu urrp po os se e
pprroodduuccttss S Sppaarrkklliinngg C Clleeaann
M Mu ullttii--p pu urrp po os se e
p prro od du uc ctts s E Ex xttrra a D Drry y
H0
H0
H0
H I
H I
H I
H2
H2
H2
• Proceed to set the water softener
— This feature is adjusted using the “S
ET
” ; button; hold down this button to access the menu. Then
press once to set the softener level.
— The softener level is then shown on the screen from
H H0 0
to
H H6 6
. The default level is
H H4 4 ..
— In order to use multi-function tablets, you need to adjust the setting. To do this, press either arrow but-
ton several times until you have selected
H H0 0
or
H H II
or
H H2 2
depending on the water hardness.
• Proceed to set the “Multi-prupose products ” function (optional)
— Hold down the “S
ET
” button until the “Multi-purpose products” light flashes, then press one or
other of the selection buttons
.
— (Light unlit) : deactivates the “Multi-purpose products” option.
— (Light flashing)
:
corresponds to activation of the “Multi-purpose products” function with the
setting for ““S Sp pa arrk klliin ng g C Clle ea an n””.
T Th hiis s e en na ab blle es s y yo ou u tto o p prriio orriittiis se e a a b brriilllliia an ntt ffiin niis sh h ffo orr y yo ou urr c crro oc ck ke erry y..
— (Light permanently lit)
:
corresponds to activation of the “Multi-purpose products” function with the
setting for ““E Exxttrra a D Drryy””.
““E Ex xttrra a d drry y”” e en nh ha an nc ce es s tth he e d drry yiin ng g rre es su ulltts s iiff p pe errffo orrm ma an nc ce e iis s rre ed du uc ce ed d..
— The setting is validated automatically after 10 seconds if the “ S
ET
” button in not pressed again.
— The “Multi-purpose products” light then illuminates permanently if this option has been selected.
45°C 65°C 55°C 45°C