Blagdon Pump 25 Series Скачать руководство пользователя страница 1

Страница: 1 / 16

HG-CF-1101 Rev. C – 19.05.06

Page 1

B25 & X25

25 Series 1” Models

This pump is Atex approved for use

in potentially explosive atmospheres

Group II category 2

SERVICE & OPERATING MANUAL

AIR OPERATED DOUBLE DIAPHRAGM PUMP

All models, BSP
Flanged models :- 1” ANSI 150.
Atex Certified models.

NOTE!

Refer to pump Typical Code matrix on page 6 to determine the full Model No. of your

pump.

Please read all warnings and instructions before using this product.

IMPORTANT

This pump should be used in accordance with the requirements of the Health and Safety at Work Act 1974.

All business conducted subject to Blagdon Pump. Terms and Conditions of Sale, available on request.

A Unit of IDEX Corporation

II 2 GD c

57470

31783

B2500T5…. Virgin PTFE / HDPE

X250044…. All Conductive PTFE

This Manual covers the following models :-

Содержание 25 Series

















Результаты поиска

Содержание 25 Series

Отзывы:

Похожие инструкции для 25 Series

Бренды по названию

Популярные бренды

Blagdon Pump 25 Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 25 Series

Отзывы:

Похожие инструкции для 25 Series

Бренды по названию

Популярные бренды