background image

6

EN

First Flight Preparation

•  Remove and inspect contents

•  Begin charging the flight battery

•   Install the flight battery in the quadcopter  

(once it has been fully charged)

•  Program your computer transmitter

•  Bind your transmitter

•  Familiarize yourself with the controls

•  Find a suitable area for flying

Flying Checklist

 

Always turn the transmitter on first

 

 Plug the flight battery into the lead from the  

4-in-1 control unit

 

 Allow the 4-in-1 control unit to initialize and  

arm properly

 

Fly the model

 

Land the model

 

 Unplug the flight battery from the 4-in-1 control unit

 

Always turn the transmitter off last

CAUTION:

 All instructions and warnings must be 

followed exactly. Mishandling of Li-Po batteries can 

result in a fire, personal injury and/or property damage.

•  NEVER LEAVE CHARGING BATTERIES UNATTENDED.

•  NEVER CHARGE BATTERIES OVERNIGHT.

•  By handling, charging or using the included Li-Po 

battery, you assume all risks associated with lithium 

batteries.

•  If at any time the battery begins to balloon or swell, 

discontinue use immediately. If charging or discharging, 

discontinue and disconnect. Continuing to use, charge 

or discharge a battery that is ballooning or swelling can 

result in fire.

•  Always store the battery at room temperature in a dry 

area for best results.

•  Always transport or temporarily store the battery in a 

temperature range of 40–120º F (5–49° C).

•  Do not store battery or model in a car or direct sunlight. 

If stored in a hot car, the battery can be damaged or 

even catch fire.

•  Always charge batteries away from flammable 

materials.

•  Always inspect the battery before charging

•  Always disconnect the battery after charging, and 

let the charger cool between charges.

•  Always constantly monitor the temperature of the 

battery pack while charging.

•  ONLY USE A CHARGER SPECIFICALLY DESIGNED TO 

CHARGE LI-PO BATTERIES. Failure to charge the battery 

with a compatible charger may cause a fire resulting in 

personal injury and/or property damage.

•  Never discharge Li-Po cells to below 3V under load.

•  Never cover warning labels with hook and loop strips.

•  Never charge batteries outside recommended levels.

•  Never charge damaged batteries.

•  Never attempt to dismantle or alter the charger.

•  Never allow minors to charge battery packs.

•  Never charge batteries in extremely hot or cold places 

(recommended between 40–120° F or 

(5–49° C) or place in direct sunlight.

Charging Warnings

Содержание Glimpse BNF BLH2280


























Отзывы: