background image

M01E03.053

M13E11 060

Warranty Claims

1.  Prior  to  returning  any  product  to  Blacoh  based  on  a  claim  of  breach  of  Warranty  or  PTFE  Bellows 

Warranty,  a  Blacoh  Return  Request  form  must  be  completed.    The  form  will  be  reviewed  by  Blacoh  to 

determine if a Return Merchandise Authorization (RMA) number will be issued.  The issuance of an RMA 

number does not constitute Blacoh's acknowledgment or agreement that the warranty claim is justified or 

correct.

2.  If an RMA number is issued by Blacoh, customer should then deliver the product in question to the address 

specified on the RMA, freight prepaid. 

3.  All products so returned to Blacoh based on a claim of breach of Warranty or of PTFE Bellows Warranty 

must  be  cleaned,  sanitized  and  neutralized  prior  to  shipment  to  Blacoh.    Blacoh  will  not  accept  any  part 

that contains corrosive chemicals, organic cultures, blood, any harmful residue or air borne materials that 

might contaminate a breathable atmosphere or put at risk any person or property.  Any shipment that does 

not comply will be returned at the expense of the customer, or the customer will be required to arrange for 

pickup. 

4.  HAZMAT SHIPMENTS WILL BE REMOVED AND PROCESSED AT CUSTOMER'S EXPENSE.
5.  Receipt  by  Blacoh  of  a  return  does  not  constitute  Blacoh's  agreement  that  Blacoh  is  in  breach  of  its 

Warranty or PTFE Bellows Warranty. 

6.  If  Blacoh  determines  that  a  defect  in  workmanship  or  material  of  a  part  has  occurred,  customer  is  not 

entitled  to  a  complete  unit  replacement.    In  the  event  of  such  a  defect,  Blacoh  will  repair  or  replace  the 

defective part or parts or refund the purchase price, as Blacoh deter

mines in Blacoh’s sole discretion. 

New Product Returns

1.  If  a  customer  wishes  to  return  a  new,  unused  product,  the  customer  must  first  request  a  Return 

Merchandise Authorization (RMA) number from Blacoh.   Blacoh will determine if the unit can be returned 

for possible credit.   

2.  Product to be returned must be new, unused, and of current design and purchased within thirty (30) days 

of  the  return  request.      In  addition  the  product  must  not  have  been  damaged  after  original  shipment  by 

Blacoh.

3.  Product returns must be delivered, freight prepaid. 
4.  Blacoh has the right to inspect all returned products prior to acceptance or rejection. 
5.  ALL  RETURNS  are  subject  to  a  minimum  $25.00  or  20%  restocking  fee,  whichever  is  greater.    (Higher 

restocking  fees  may  be  charged  on  special  items  and  some  models  may  not  be  eligible  for  return).  

Returns accepted by Blacoh will be credited to the customer's account less the re-stocking fee.  Refunds 

will not be issued. 

6.  Any outsourced product supplied by Blacoh will be subject to the warranty, return policy and re-stock fee 

charged by the manufacturer of the outsourced product. 

 [L01E71.053] 

BLACOH F

LUID 

C

ONTROL

, I

NC

.

601 Columbia Ave, Bldg D 

Riverside, CA 92507  USA 
Phone:  951.342.3100 

 

800.603.7867 

Fax: 

951.342.3101 

Email:  [email protected] 

www.blacoh.com 

Содержание Sentry













Отзывы: