manualshive.com logo in svg

BLACKMER LGB1E, Инструкции по установке, эксплуатации и обслуживанию

Поделиться
Скачать
BLACKMER LGB1E Скачать руководство пользователя страница 2

501-A00    Page 2/12 

SAFETY DATA 

 

Failure to disconnect and lockout 
electrical power or engine drive before 
attempting maintenance can cause 
severe personal injury or death 

 

Failure to disconnect and lockout 
electrical power before attempting 
maintenance can cause shock, burns or 
death 

 

Hazardous 

machinery can 

cause serious 

personal injury.

 

 

Hazardous voltage. 

Can shock, burn or 

cause death.

 

 

 

 

 

 

 

Disconnecting fluid or pressure 
containment components during pump 
operation can cause serious personal 
injury or property damage.

 

 

Failure to relieve system pressure prior 
to performing pump service can cause 
serious personal injury or property 
damage.

  

Systems with meters will still 

be pressurized even after the hose is 
emptied

 

 

 

Hazardous pressure 

can cause serious 

personal injury or 

property damage 

 

Hazardous pressure 

can cause serious 

personal injury or 

property damage

 

 

 

 

 

 

 

If pumping hazardous or toxic fluids, 
system must be flushed and 
decontaminated, inside and out, prior to 
performing service or maintenance 

 

Operation without guards in place can 
cause serious personal injury, major 
property damage, or death. 

 

 

Hazardous or toxic 

fluids can cause 

serious injury. 

 

Do not operate 

without guard  

in place 

 

 

 

 

 

 

PUMP DATA 

PUMP IDENTIFICATION 

A pump Identification tag, containing the pump serial number, I.D. number, and model designation, is attached to each pump.  It is 
recommended that the data from this tag be recorded and filed for future reference. If replacement parts are needed, or if 
information pertaining to the pump is required, this data must be furnished to a Blackmer representative. 

 

TECHNICAL DATA 

Maximum Pump Speed 

1,750 RPM 

Maximum Operating Temperature 

240°F 

(115°C) 

Maximum Differential Pressure 

125 psi 

(8.6 Bar) 

Maximum Working Pressure 

350 psi 

(24.1 Bar) 

 

 

Technical Data is for standard materials of 
construction.  Consult Blackmer Material Specs for 
optional materials of construction. 

 

These pumps are listed by Underwriters’ Laboratories 
for liquefied petroleum gas and NH

3

 service. 

INITIAL PUMP START UP INFORMATION 

Model No.: ____________________________________ 

Serial No.:  ____________________________________ 

ID No.:  _______________________________________ 

Date of Installation: _____________________________ 

Inlet Gauge Reading: ____________________________ 

Discharge Gauge Reading: _______________________ 

Flow Rate: _____________________________________ 

 

Содержание LGB1E













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды