manualshive.com logo in svg

BLACKHAWK! V-2, Руководство по установке и эксплуатации

Поделиться
Скачать
BLACKHAWK! V-2 Скачать руководство пользователя страница 9

Preintstallation

Installation

Startup

Maintenance

Troubleshooting Guide

Preintstalla

tion

 

Blackhawk Technology Company

V-2PneumaticPistonPumpI&O-10365  |  20220811    

7

6 .  LAY OUT THE DOWNHOLE COMPONENTS  

OF THE PUMP SYSTEM

a.  Lay out the pump system.
b. The well seal will be at the top and a stain-

less-steel pipe nipple will be threaded into 

the bottom. The nipple will provide rigidity 

and quick access to the fiberglass drive rod if 

it slips down the well. 

c.  At the bottom of the pump system is the 

screen and pump barrel. 

 

⸰

If the ID of the riser pipe or the connec-

tions is smaller than the piston’s diameter, 

then a pipe nipple will be added to the 

top of the pump barrel for  maintenance 

purposes. 

d. The middle gap is where you will connect 

the riser pipe. The length of the riser pipe is 

dependent on the length of the well, minus 

the lengths of the pump barrel and the pipe 

nipples provided. 

Содержание V-2





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды