manualshive.com logo in svg

BLACKHAWK! PL10C, Инструкция по эксплуатации

Поделиться
Скачать
BLACKHAWK! PL10C Скачать руководство пользователя страница 18

________________________________________PL10C / PL20B_____________________________________

 

18 

IX) TROUBLESHOOTING 

 

Detection and repair of faults, if any, should only be done subject to the condition that all the relevant SAFETY 

REGULATIONS as described are followed strictly. 

 
ALL  RESETTING  ACTIONS,  REPAIRS  TO  THE  SAFETY  DEVICES  AND  THE  ELECTRICAL  CONTROLS  OF  THE 

LIFT SHOULD BE CARRIED OUT BY AUTHORISED PERSONNEL ONLY. 

 

Problem 

Cause 

Solution 

The lift does not rise when the 

lifting button is pressed.  

The fuse is burnt out 

Replace the fuse 

The lift is heavily overloaded 

Reduce the load to the maximum 

weight according to the 

specifications. 

The switch is not working 

Call dealer to replace the switch  

Fault in the electrical system 

Call dealer for service 

Too little hydraulic oil 

Fill in hydraulic oil 

The lift does not lift the whole way. 

The lift is overloaded 

Maintain max. weight according to 

specifications 

Too little hydraulic oil 

Fill in hydraulic oil. 

The platform moves downwards 

whereas the descent button is not 

pushed. 

Leakage in hydraulic system 

Call dealer for service 

The hydraulic cylinder is dirty 

Call dealer for service 

Non return valve is leaking 

Call dealer for service 

Lift does not respond while pushing 

the descent button.  

Defect in electric system 

Call dealer for service 

An obstacle prevents the mobile 

leg of the lift from moving 

Remove any object preventing the 

moving of the bearings. 

Thoroughly clean and grease the 
surface on which the mobile leg of 

the lift moves by the means of the 

bearings. 

 
SPARE ORDERING / REPAIR PROCEDURE 

 

To order spare parts, it is necessary to indicate the lift and pump serial numbers as well as the year of manufacturing. 

Содержание PL10C







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды