background image

TA04721  B   Page 5 of 8  

COMPRESSION OPERATION

3.5

1. Select the appropriate size dies for the connector being used. 
2. Insert the Dies into the Head side and Ram side by sliding the 

dies in while pressing the Die Release Pin. If needed, the 
head can be opened for easier access by pulling the Head 
Release Pin. 

IMPORTANT:

 Prior to compression, make sure 

the head is closed and the Head Release Pin is fully 
engaged.

3. Place the connector between the dies. Press the advance 

button and advance the Ram so the connector is held lightly 
between the dies. Do not deform the connector.

4. Insert the conductor into the connector.
5. Press the advance button until the compression is complete. 

A series of clicks will be heard followed by a release in the 
pressure when compression is complete. If the LED indicator 
(Step 2.1) shows RED during compression, the battery 
charge level is low but enough to complete the compression. 
The battery should be charged before next use.

6. Press the release button (Step 3.4) to retract the ram. The 

ram continues to retract while the release button is pressed. 
The ram stops when it is fully retracted.

7. Remove the compressed connector from the tool. 

Dies

Die Release Pin

(Head Side)

Die Release Pin

(Ram Side)

Head Release Pin

WARNING

Pinch point hazard. Compression Dies at high 
force can cause severe personal injury. Keep 
all body parts away from moving parts of the 
tool during operation.

MAINTENANCE & INSPECTION

3.6

1. Very little maintenance is required to ensure that the tool is kept in good working condition.
2. To ensure smooth operation and prevent rust, store the tool in a cool dry area. Ensure that moving parts are lubricated regularly.
3. When the plastic housing becomes dirty, clean it with a soft soaped cloth.
4. Dust, sand, and dirt are a danger for any hydraulic device. After each use, the tool should be wiped with a clean cloth taking care 

to remove any residue, especially close to the movable parts.

5. If the tool is maintained regularly, it should provide you with trouble free service.

NOTE:

 Always remove the battery pack from the unit before replacing parts or maintenance.

TROUBLE SHOOTING

3.7

Problem

Cause

Solution

Charger LED lamp indicates stand by while battery

is inserted. 

There is dust or foreign objects lodged at 

the battery contacts.

Remove foreign objects.

The charger LED lamp indicates high or low

temperatures. 

The battery is too hot or cold.

Allow the cartridge to reach room temperature

before continuing. 

The motor does not operate at all.

The battery is not charged or defective. 

Charge or replace the battery.

There is dust or foreign objects lodged at

the battery contacts. 

Remove foreign objects.

The switch is misaligned.

Check to see if switch is aligned with advance

button, consult tool service. 

The motor runs but ram will not advance, or ram

advances but will not build pressure. 

Consult tool service.

Air in hydraulic system.

Insufficient hydraulic oil.

Hold the tool with head towards the floor to

allow air to rise towards top of oil bladder.

Defective hydraulic circuit.

Consult tool service.

The ram will not retract

Tool did not complete a full cycle and

bypass.

Depress advance button and allow tool to 

reach full pressure and bypass, then depress 

release button to retract the ram.  

The connector is jammed in compression

dies. 

Depress and hold release button while prying

compression dies apart. 

The release button is bent or misaligned.

Consult tool service.

Содержание TBM15CR-LI









Отзывы: