manualshive.com logo in svg

Black Horse Model Focke-Wulf FM 190A, Инструкция по эксплуатации, Страница: 23 / 32

Поделиться
Скачать
Black Horse Model Focke-Wulf FM 190A Скачать руководство пользователя страница 23

23

Focke-Wulf  FW190A-

Item code:BH87

                              INSTRUCTION MANUAL.

Epoxy glue

Epoxy glue

90º

Vertical

Stabilizer.

Horizontal

Stabilizer.

Epoxy glue

 

5.  Put the  vertical  stabilizer  back  in

place. Using a  triangle,  check  to  ensure
that  the vertical stabilizer is aligned 90 de-
gree to the horizontal stabilizer.

C/A glue

 

6) When you are sure that everything is a

aligned correctly, mix up a generous amount
of 30 minute epoxy. Apply a thin layer to the
slot in the mounting platform and to the verti-
cal stabilizer mounting area. Apply epoxy to
the lower rudder hinge. Set the stabilizer in
place and  re-align. Double check all of your
measurements once more before the epoxy
cures. Remove any excess epoxy using a
paper towel and rubbing alcohol and hold the
stabilizer in place with T-pins or masking tape.
Allow the epoxy to fully cure before proceed-
ing.

C/A glue

C/A glue

Содержание Focke-Wulf FM 190A

































Отзывы:

Нет отзывов