background image

L-39 Albatros                    Item code: BH183

Instruction Manual

   When ready to fly, first extend the transmitter aerial.

   Switch on the transmitter.

   Switch on the receiver.

   Check that the wings are correctly fitted to the

   fuselage.

   Operate the control sticks on the transmitter and 

   check that the control surfaces move freely and in

   the CORRECT directions.

   Check that the transmitter batteries have adequate 

   power.

   ALWAYS take off into the wind.

   If the model does not respond correctly to the 

controls, land it as soon as possible and correct the 

   fault.

   ALWAYS land the model INTO the wind, this ensures

   that the model lands at the slowest possible speed.

   Switch off the receiver.

   Switch off the transmitter.

   Empty the fuel tank after flying, fuel left in the tank 

   can cause corrosion and lead to engine problems.

A. GENERAL: A model aircraft is a non-human-carrying aircraft capable of sustained flight in the atmosphere. It may 

not exceed limitations of this code and is intended exclusively for sport, recreation, education and/or competition. 

All model flights must be conducted in accordance with this safety code and anyadditional rules specific to the 

flying site.

1.  Model aircraft will not be flown:

(a) In a careless or reckless manner.

(b) At a location where model aircraft activities are prohibited.

2.  Model aircraft pilots will:

(a) Yield the right of way to all human-carrying aircraft.

(b) See and avoid all aircraft and a spotter must be used when appropriate. (AMA Document #540-D.)

(c) Not fly higher than approximately 400 feet above ground level within three (3) miles of an airport without notifying 

the airport operator.

(d) Not interfere with operations and traffic patterns at any airport, heliport or seaplane base except where there is a 

mixed use agreement.

(e) Not exceed a takeoff weight, including fuel, of 55 pounds unless in compliance with the AMA Large Model 

Airplane program. (AMA Document 520-A.)

(f)  Ensure the aircraft is identified with the name and address or AMA number of the owner on the inside or affixed 

to the outside of the model aircraft. (This does not apply to model aircraft flown indoors.)

(g) Not operate aircraft with metal-blade propellers or with gaseous boosts except for helicopters operated under the 

provisions of AMA Document #555.

(h) Not operate model aircraft while under the influence of alcohol or while using any drug that could adversely affect 

the pilot’s ability to safely control the model.

(i)  Not operate model aircraft carrying pyrotechnic devices that explode or burn, or any device which propels a 

projectile or drops any object that creates a hazard to persons or property.

Exceptions:

•    Free Flight fuses or devices that burn producing smoke and are securely attached to the model aircraft during 

flight.

•   Rocket motors (using solid propellant) up to a G-series size may be used provided they remain attached to the 

model during flight. Model rockets may be flown in accordance with the National Model Rocketry Safety Code 

but may not be launched from model aircraft.

Academy of Model Aeronautics National Model Aircraft Safety Code

Effective January 1, 2014

FLIGHT WARNINGS

ADHESIVES AND REQUIRED TOOLS

Top Flite® MonoKote® Sealing Iron 

Top Flite Hot Sock Iron Cover 

Top Flite MonoKote Trim Seal Iron 

Top Flite MonoKote Heat Gun 

COVERING TOOLS

Thin CA 

30-minute epoxy 

6-minute epoxy

Threadlocker thread locking cement 

Mixing sticks 

Mixing cups (GPMR8056)

Epoxy brushes 

Denatured alcohol 

Canopy Glue 

Felt-tipped pen or pencil 

Flat screwdriver

Adjustable wrench 

Drill

Hobby knife 

Masking tape

Phillips screwdriver (large) 

Phillips screwdriver (small)

Ruler 

Sandpaper

Soldering iron

Solder

Hex wrench

Drill bit: 1/16-inch (1.5mm), 5/64-inch (2mm), 

1/8-inch (3,2mm), 3/16-inch (4,8mm),11/64-inch 

(4.5mm), 13/64-inch (5,2mm), 1/4-inch (6,4mm)

4

Содержание BH183










































Отзывы: