background image

September

 2018

CLEANING - NOTE:

 To maintain cleanliness and increase service life, this item should be cleaned daily. Do not immerse the 

unit in water or any other liquid, if liquid enters the electrical compartment it may cause a short circuit or electrical shock.

1.

Before cleaning or attempting to move this item always turn off and unplug.

2.

Wipe the entire unit with a clean soft cloth until it is completely dry.

3. To avoid damage to the unit, do not use abrasive cleaners or scouring pads.

4. If soap or chemical cleaners are used, be sure they are completely rinsed away with clean water immediately after

cleaning. Chemical residue could damage or corrode the surfaces of the unit.

5.

After using of the machine, please remove the flat beater, dough hook, wire whip and meat grinder from the machine

and wash these parts thoroughly in hot, soapy water to prevent the growth of bacteria.

6. When clean and maintain the inside of the protective cover and swivel mount, please loosen the screw around the

protective cover and take off the protective cover. If there is no sign of oil leak, no need to take off the swivel mount.

Clean the swivel mount with a wet cloth, the protective cover can be cleaned by detergent and washed under the wa-

ter supply tap. After washing by clean water, use dry cloth to wipe out the water and make it dry.

To avoid serious injury or damage, never attempt to repair or replace a damaged power cord yourself.  Contact a professional repair 

service. 

Problem

Possible Causes

Solution

The axles don’t work when 

operating the machine

Electrical connection is not 

good

Check the plug in the outlet

Leaking oil

oil gaskets are worn out or 

damadged

Replace the oil gasket(s)

Difficult to raise or lower the 

bowl

Either the slideway is 

corroded, or the lead screw, 

bevel gear or hand wheel 

shaft is dried out

Clean and oil the dried out 

parts

Motor is overheating and 

speed has decreased

The voltage is not enough, 

incorrect speed is set or there 

is too much food in the bowl

Check the voltage or adjust 

the speed to a better setting. 

If the bowl is overloaded, 

remove some of the food to 

lighten the load

Item is making too much 

noise and overheating

Poor lubrication

Add or replace oil

Agitator touches bowl

Either the bowl or agitator    

is deformed

Repair or replace deformed 

part

Mixing bowl is out of position  Moving direction is not 

correct

Adjust position

TROUBLESHOOTING

Net weight: 326 lbs (148 KGS)
Dimensions: 25” x 21” x 39.5” (640 X 530 X 1000 mm)

Содержание BDPM-30











Отзывы: