Black Box SDSL Network Extender 2000 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 22

background image

16

SDSL NETWORK EXTENDER 2000

4. Operation

While the SDSL Network Extender 2000 is operating,
you can inspect the front-panel LEDs on its Units at any
time for status information:

LED

Meaning

Connection

Pulses green once per second to show that
the SDSL connection is operational and the
Unit is receiving either valid data packets or
status packets from the other Unit.

Power

Steadily lit green to show that the Unit is
receiving AC power.

Collision

Flashes red every time there’s a collision on
the attached Ethernet segment.

Rx

Flashes amber every time a data packet is
received from the attached Ethernet
segment. Steadily lit amber to show that no
SDSL connection is present.

Tx

Flashes amber every time a data packet is
sent to the attached Ethernet segment.
Steadily lit amber to show that no SDSL
connection is present.

«
...
15
16
17
18
19
...
»

Содержание SDSL Network Extender 2000























Отзывы:

Нет отзывов

Похожие инструкции для SDSL Network Extender 2000

Crispin ST-FP9076

Бренд: Saturn Страницы: 11

Бренд: Oster Страницы: 38

AVO-A2-MINI-WP-F

Бренд: Intelix Страницы: 2

Бренд: B&B Electronics Страницы: 2

Бренд: Morris Страницы: 7

Бренд: Becken Страницы: 40

Бренд: Hamilton Beach Страницы: 3

Delight BL510BWS

Бренд: Tesla Страницы: 52

NVF-200SE/PD KIT

Бренд: netsys Страницы: 39

Бренд: Abocom Страницы: 2

Бренд: Nutri Ninja Страницы: 2

Бренд: Exido Страницы: 26

Бренд: Exido Страницы: 32

Бренд: Elvox Страницы: 8

Бренд: Morphy Richards Страницы: 8

Easy Blend 48415

Бренд: Morphy Richards Страницы: 12

Бренд: Trisa Страницы: 23

Бренд: Trisa Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды