background image

1

SAFETY

Safety

READ THIS FIRST!

1. Do not connect the Active Star Hubs to any type of public network.

2. Do not connect any outdoor cabling to the Active Star Hubs without proper

lightning protection.

3. Do not use unauthorized power supplies or cables with the Active Star Hubs.

4. Do not connect the Active Star Hubs to non-5250 protocol devices.

5. Do not disassemble or modify the power supply and its cables.

6. Do not open the Active Star Hubs that are connected to power or data cables.

Disconnect all cables before configuration.

7. Devices attached to the UTP network must comply with the voltage and

current limits for Class 2 Power-Limited Signal Circuits as defined by article
725 of the National Electrical Code and Section 16 of the Canadian Electrical
Code.

8. For your safety, receptacles must be properly wired and grounded.

9. Never attempt to service equipment connected to the data cable network or

to the grounded receptacle during an electrical storm. Exposure to lethal
voltages may occur when lightning is present.

The following FCC statement applies to the Active Star Hubs.

IC207A/8A-Manual  7/12/00  9:31 AM  Page 1

Содержание Multi Quick Check RJ-11



















Отзывы: