Black Box ME280A-35 Скачать руководство пользователя страница 47

Страница: 47 / 48

SHM-768K

To install two units follow these instructions:

1. Fasten one long side rail to each unit (one on the right side of one

unit, the other on the left side of the other unit) using the 4 screws and
flatwashers supplied. The side rails must be attached in opposing fashion,
the narrow flange of the first rail opposite the wide flange of the second
rail.

2. Attach one short bracket opposite the side rail on each unit using

the 4 screws and flatwashers supplied.

3. Slide the side rail of one unit into the side rail of the other unit,

fastening the two units together. See Figure 3-3.

4. Secure the supplied plastic caps to the ends of the rails, to prevent

the units from moving and to protect the rail ends.

Place the assembled units in the rack and fasten the brackets to the

side rails of the rack, by means of the four screws situated on each side
(not included in the kit).

Figure B-3. Installation of Two Units, Part 2.

Содержание ME280A-35
















































Результаты поиска

Содержание ME280A-35

Отзывы:

Бренды по названию

Популярные бренды

Black Box ME280A-35, Руководство пользователя

Результаты поиска

Содержание ME280A-35

Отзывы:

Бренды по названию

Популярные бренды