Black Box IE GIGA MC TX/SFP Скачать руководство пользователя страница 20

Страница: 20 / 56

Chapter 3: Configuration

Page 20

724-746-5500 | blackbox.com

LGC340A

3.5.3 Commands List (Space Bar)

The IE GIGA MC TX/SFP also includes several device-specific options. To

access these options, press the

Space Bar

from the Main Configuration

screen, type the name of the action to be performed (as shown below) and

press

Enter

Command

Description

cleandb

Reboots the unit with a clean database. This removes all information

from the database and sets the unit to factory defaults.

download

Downloads firmware via the TFTP protocol

accounts

Allows the addition for User, Superuser, Admin

vlan

Provides selection of two modes of operation to support all VLAN

configurations.

Displays settings for Bandwidth configuration

version

Displays the unit’s firmware and hardware version

ifstats

Displays interface statistics

rmstats

Displays remote monitoring (RMON) statistics on packets received as

defined in RFC 2819 for RMON.

sysDescr

Allows the editing of sysName, sysDescr, and Port information

reboot

Allows a soft reboot of the unit after changes are made by the end

user

oam

Enable/disable OAM

sfpstats

Provides information about the wavelength, serial number, output

power, BER and other information. Requires an SFP with DDMI.

unit

Unit global settings, frame size selection. Unit OAM enable must be

enabled for AH and AG to function.

port

Displays the port status and allows changes to port settings, such as

duplex status and speed.

3.5.3.1 Cleandb

Entering cleandb reboots the unit with its database cleaned depending on the

option selected. Users are presented with two, sequential options, first to reset

Chapter 5: Operation

LGC340A

724-746-5500 | blackbox.com

Page 37

5. Operation

5.1 LED Operation

Each IE GIGA MC TX/SFP includes SFP and RJ-45 LEDs.

SFP LED functions are as follows:

LED

Function

FLT

Glows amber when a fault is detected.

LNK

Glows green with a valid optical link.

ACTIVE Glows green when the port is active.

OFF when SFP is in standby (does not indicate activity).

OAM

Glows green when an active OAM channel is established.

RJ-45 LED functions are as follows:

LED

Function

LNK/ACT

Glows green when a link is established on the TX port.
Blinks green when activity is detected on the TX port.

FDX

Glows amber when an FDX link is established on the TX port.
Not lit for HDX.

5.2 Autocross Feature for Twisted Pair Connections

All fixed twisted pair ports on the IE GIGA MC TX/SFP include AutoCross, a

feature that automatically selects between a crossover workstation and a

straight-through connection depending on the connected device.

5.3 Using iView

iView² is Black Box’s management software, providing network management in

an easy to use GUI. Once iView² is installed on a network management PC

using a Windows operating system, use the Start menu to access iView².

NOTE

Windows SNMP services must be installed to receive traps.

Содержание IE GIGA MC TX/SFP

























































Результаты поиска

Содержание IE GIGA MC TX/SFP

Отзывы:

Похожие инструкции для IE GIGA MC TX/SFP

Бренды по названию

Популярные бренды

Black Box IE GIGA MC TX/SFP, Руководство пользователя

Результаты поиска

Содержание IE GIGA MC TX/SFP

Отзывы:

Похожие инструкции для IE GIGA MC TX/SFP

Бренды по названию

Популярные бренды