Agility Zero U Transmitter
Quick Start
continued overleaf
Welcome
This quick start guide covers some of the key points of the Agility Zero U Transmitter. Full user details
and setup instructions can be found within the Support section at
www.blackbox.com
Initial configuration
Please see the next page for
Connection
details.
Agility units can be linked in two main ways: Direct or Networked.
Direct linking
Where Agility transmitters and receivers are directly linked to each other, very little configuration
action is required, provided that they both have their factory default settings in place - just link them
together. If the standard settings have been changed in a previous installation, you merely need to
perform a
manual factory reset
on each unit. Please see the next page for further details.
Safety information
•
For use in dry, oil free indoor environments.
• Not suitable for use in hazardous or explosive environments or next to highly flammable materials.
•
No user serviceable parts are contained within the module - do not dismantle.
Radio Frequency Energy
All interface cables used with this equipment must be shielded in order to maintain compliance
with radio frequency energy emission regulations and ensure a suitably high level of immunity to
electromagnetic disturbances.
European EMC directive 2014/108/EC
This equipment has been tested and found to comply with the limits for a class A
computing device in accordance with the specifications in the European standard EN55032.
In a residential environment, this equipment may cause radio interference.
FCC Compliance Statement (United States)
This equipment generates, uses and can radiate radio frequency energy and if not installed and used
properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to
radio communication. It has been tested and found to comply with the limits for a class A computing
device in accordance with the specifications part 15 of FCC rules, which are designed to provide
reasonable protection against such interference when the equipment is operated in a commercial
environment. Operation of this equipment in a residential area may cause interference, in which case
the user at his own expense will be required to take whatever measures may be necessary to correct
the interference. Changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
Canadian Department of Communications RFI statement
This equipment does not exceed the class A limits for radio noise emissions from digital apparatus set
out in the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de la classe A prescrites dans le règlement sur le brouillage radioélectriques publié par le
ministère des Communications du Canada.
Agility RX
Agility
Zero U TX
Agility RX
Agility RX
Agility RX
Gigabit
Ethernet
Agility
Zero U TX
Networked linking
Where Agility units are connected via networked links, you can either configure them individually, or
configure them collectively using an iPATH Manager:
•
Configuring networked Agility units individually
- You need to specify the network
addresses of the Agility units so that they can locate each other. This is done by running the Agility
browser-based configuration utility on a computer system linked to the same network as the
Agility units. Please see the next page for further details.
•
Configuring networked Agility units collectively
- The iPATH Manager allows you to
configure, control and coordinate any number of Agility transmitters and receivers from a single
application. See blackbox.com for details.
IMPORTANT: When using an iPATH Manager to configure
Agility units, it is vital that all units that you wish to locate
and control are set to their factory default settings.
Otherwise they will not be located by the iPATH Manager.
If necessary, perform a manual factory reset on each
Agility unit. See next page.
Note: If you are using one or more Agility Zero U
Transmitters within an installation managed by an iPATH
Manager, the iPATH Manager must be running firmware
version 4.7 or above.
We‘re here to help! If you have any questions about your application or our products, contact
Black Box Tech Support at 877-877-2269 or go to blackbox.com and click on “Talk to Black Box.”
You’ll be live with one of our technical experts in less than 60 seconds.
ACR500DP-T
ACR500DV-T
ACR500VG-T
