Black & Decker Tradesman KTG15, Руководство пользователя, Страница: 6 / 24

6
ENGLISH
electrically insulated from the mains power supply.
This is done by placing insulated barriers between
the electrical and mechanical components so as to
making unnecessary for the tool to be earthed.
NOTE: Double insulation does not takethe place of normal
safety precautions when operating this tool. The insulation
system is for added protection against injury resulting from a
possible electrical insulation failure within the tool.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the volt-
age on the rating plate.
@
Warning: Never connect the live (L) or neutral (N)
wires to the earth pin marked E or .
Using an Extension Cable
An extension cable should not be used unless absolutely
necessary. Use of an improper extension cable could resultin
a risk of fire and electric shock. If an extension cable must
be used, use only those that are approved by the country's
Electrical Authority. Make sure that extension cord is in good
condition before using. Always use the cord that is suitable
for the power input of your tool (see technical data on name
plate). The minimum conductor size is 1.5mmWhen using a
cable reel, always unwind the cable completely.
Description (Fig. A)
Your Black & Decker small angle grinder has been designed
for grinding, cutting, wire-cup brushing and sanding
applications.
1. On/off switch (toggle version KTG15T switch at rear)
2. Side handle*
3. Spindle lock
4. Wheel guard
5. Inner flange
6. Outer flange
* Not all models contain side handle
Assembly and Adjustment
@
Prior to assembly and adjustment always unplug the
tool.
Mounting and Removing the Guard (Fig. B)
Mounting
u
Place the angle grinder on a flat and steady surface,
spindle (7) up (fig. B1)
u
Align the 3 lugs (8) with the 3 slots (9) in gearcase cover.
u
Press the guard (4) down and turn it in the direction of the
arrow until it is in the working position providing maximum
protection to the user (fig. B2)
u
Insert the bolt (11) to the holes on the bracket. Screw
the nut (12) on the thread of the bolt. Use crosshead
screwdriver (13) (not supply) to tighten the bolt and nut.
@ Do not operate the grinder with a loose guard.
Removing
u
Follow the procedure above in reverse order.
Mounting and Removing Grinding Wheels or
Cutting Discs (Fig. C & D)
Your grinder comes with two reversible flanges to
accommodate a wide variety of different accessories. Make
sure the correct sides of the flanges are being used ensuring
no excessive play between the accessory and the flanges.
Mounting
u
Place the inner flange (5) on the grinder spindle (7) (fig.
C1)
u
Place the wheel (14) against the flange. Screw the
threaded flange (6) onto the spindle (7). (fig. C2).
u
Make sure that the threaded outer flange (6) is facing in
the correct direction for the type of disc fitted. For grinding
discs, the flange (6) is fitted with the raised portion facing
towards the disc (fig. C3). For cutting discs, the flange(6)
is fitted with the inner portion facing away from the disc
(fig. C4).
u
Press in the spindle lock button (3) and rotate the spindle
until it locks. Keeping the lock button pressed in, tighten
the threaded flange (6) with the spanner (15) provided
(fig. D)
Release the spindle lock.
Removing
u
Follow the procedure above in reverse order.
Fitting a Wire Cup Brush
u
Screw the wire cup brush directly onto the spindle without
using the inner and threaded flanges.
Mounting and Removing the Rubber Backing Pad
(Fig. D & E)
The rubber-backing pad is available as an option. The guard
is not required when using the tool for sanding with the