Black & Decker PAD120, Руководство пользователя, Страница: 5 / 12

Unclip the handle (2) from the appliance.
Rotate the locking ring (3) anti-clockwise to release
the clips.
Pull the hose (4) away from the handle (2).
Fit the accessory directly to the hose cuff (11).
To refit the handle:
Remove the accessory from the hose.
Push the hose (4) into the handle (2). Rotate the
locking ring (3) clockwise until it clicks into place.
Use
Connecting to a power source using the 12 Vdc
accessory plug (fig. C and D)
Note: The tip of the plug is positive (+) and the side
contact is negative (-).
Remove the 12 Vdc accessory plug (12) from the
storage recess (13) on the base of the appliance.
Unclip the cord clip (14) from the cord storage.
Fully unwind the cord from the cord storage (15).
Connect the appliance to the power source by
inserting the 12 Vdc accessory plug (12) firmly into
the accessory outlet of a vehicle or other dc power
source.
Note: On some vehicles the accessory socket may only
become live when the ignition key is in the accessory
position.
Warning! Do not use with positive ground electrical
systems, (i.e older vehicles).
Warning! A reverse polarity connection will result in a blown
fuse and may cause permanent damage to the appliance.
When you have finished using the appliance:
Remove the 12 Vdc accessory plug (12) from the
12Vdc source.
Wind the cord onto the cord storage (15) and secure
with the cord clip (14).
Store the 12 Vdc accessory plug (12) in the storage
recess (13) in the base of the appliance.
Switching on and off
To switch the appliance on, slide the on/off power
switch(1) to the right.
To switch the appliance off, slide the on/off power
switch(1) to the left until it clicks into the off position.
The appliance can be used for periods of up to 30 minutes
without noticeably affecting the power of a normally charged
car battery in good condition.
Warning! Extended use will drain the battery power. Do not
run the vehicle’s engine while cleaning as this can shorten
the life of the appliance.
Vacuuming
When operating the appliance, make sure that the
hose is not trapped, twisted or blocked.
The handle (2) can be easily removed from the
appliance allowing you to reach up to 1.5 m from the
appliance.
With the handle (2) removed, the appliance can be
carried using the built-in handle.
The handle (2) can also be removed from the hose (4)
so that you can connect an accessory directly to the
hosecuff (11) when required.
Optimising the suction force
In order to keep the suction force optimised, the filters
must be cleared regularly during use.
Turn the filter cleaning wheel (5) two turns clockwise
to remove any dust from the filters.
The fine particulate filter must be cleaned regularly,
see “Cleaning the fine particulate filter” section.
Cleaning and maintenance
Your Black & Decker tool has been designed to operate over
. e c n a n e t n i a m f o m u m i n i m a h ti w e m it f o d o ir e p g n o l a
Continuous satisfactory operation depends upon proper
care and regular cleaning.
Warning! Before performing any maintenance or cleaning
on the appliance, unplug the appliance.
From time to time wipe the appliance with a damp cloth. Do
not use any abrasive or solvent-based cleaner. Do not
immerse the appliance in water.
Emptying the dust container (fig. E)
The dust container must be emptied regularly, preferably
after every use.
Release the door latch (7) and open the transparent
door (6) 180° until it clicks in the open position.
Remove the pre-filter (16).
Empty the dust container.
Clean the pre-filter (16) by lightly shaking over a
dustbin.
Refit the pre-filter (16)
Close the transparent door (6) and make sure that it
clicks into place.
Warning! Do not, under any circumstances, rinse out the
dust container.
5
ENGLISH