Black & Decker GTC650L, Руководство по эксплуатации

Страница: 8 / 12

8
ENGLISH
(Original instructions)
Charger diagnostics
If the charger detects a weak or damaged battery, the
charging indicator (9) will flash red at a fast rate. Proceed as
follows:
♦ Re-insert the battery (6)
♦ If the charging indicator continues flashing red at a fast
rate, use a different battery to determine if the charging
process works properly.
♦ If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
♦ If the new battery gives the same indication as the original
battery, take the charger to be tested at an authorised
service centre.
Note It may take as long as 60 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink red, fast and slow, one
flash at each speed and repeat.
Switching on and off (fig. C)
For your safety, this tool is equipped with a double switching
system. This system prevents starting the tool inadvertently
and will only allow operation while holding the tool with both
hands.
Switching on
♦ Squeeze the front handle switch (1).
♦ Push the lock-off button (3) forward using your thumb and
at the same time squeeze the trigger switch (2).
♦ Release the lock-off button.
Switching off
♦ Release the front handle switch (1) or the trigger switch (2).
Warning! Never attempt to lock a switch in the on position.
Hints for optimum use
♦ Slightly tilt the tool (up to 15° relative to the line of cut) so
that the blade tips point slightly towards the hedge (fig. D1).
This will cause the blades to cut more effectively.
♦ Start by trimming the top of the hedge. Hold the tool at
the desired angle and move it steadily along the line of
cut (fig. D2). The double-sided blade allows you to cut in
either direction.
♦ In order to obtain a very straight cut, stretch a piece of
string along the length of the hedge at the desired height.
Use the string (11) as a guideline, cutting just above it (fig. D2).
♦ In order to obtain flat sides, cut upwards with the growth
(fig. D3). Younger stems move outwards when the blade
cuts downwards, causing shallow patches in the hedge.
♦ Take care to avoid any foreign objects. Especially avoid
hard objects such as metal wire and railings, as these
could damage the blades (fig. D4).
♦ Regularly oil the blades.
♦ Consider purchasing a spare battery to extend the
running time of this tool. The catalogue number of the
battery is found in the technical data chart below.
Maintenance
Your Black & Decker corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Before performing any maintenance on corded/cordless power
tools:
♦ Switch off and unplug the appliance/tool.
♦ Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
♦ Or run the battery down completely if it is integral and
then switch off.
♦ Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do not
use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust from
the interior (when fitted).
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do
not dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces the
demand for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.