6
7
USE
Using the jump-starter
Caution! To reduce the risk of property damage:
• Make sure that the vehicle is in neutral with the
parking brake applied.
• Make sure that the cables are not in the path of
moving belts or the fan.
Note:
If your connections are incorrectly made, the unit will beep
continuously and the red reverse polarity indicator will
illuminate, even if the on/off switch is in the off position.
Correct the connections immediately.
1. Turn off the vehicle’s ignition and all accessories
before making any connections.
2. Make sure that the jump-starter power switch is
turned off.
3. Check polarity of battery posts. Positive (POS, P,
+) battery post usually has larger diameter than
negative (NEG, N, –) post.
4. Determine which post of the battery is grounded
(connected to the chassis). If negative post is
grounded (as in most vehicles), see 5. If positive
post is grounded, see 6.
5. For negative-grounded vehicle, connect positive
(red) clamp from battery charger to positive
(POS, P, +) ungrounded post of battery. Connect
negative (black) clamp to vehicle chassis or
engine block away from battery. Do not connect
clip to carburetor, fuel lines, or sheet-metal body
parts. Connect to heavy gauge metal part of the
frame or engine block.
6. For positive-grounded vehicle, connect negative
(black) clamp from battery charger to negative
(NEG, N, –) ungrounded post of battery. Connect
positive (red) clamp to vehicle chassis or engine
block away from battery. Do-not connect clip to
carburetor, fuel lines or sheet-metal body parts.
Connect to a heavy gauge metal part of the frame
or engine block.
Important!
If the connections to the battery’s
positive and negative terminals are incorrect,
the Reverse Polarity Indicator will light and the
unit will sound a continuous alarm until the
clamps are disconnected. Disconnect clamps and
reconnect to battery with correct polarity.
7. Turn the jump-starter power switch to the on
position.
8. Start the vehicle and crank the engine in 3 to 6
second bursts.
Important!
If the engine doesn’t start within 6
seconds let the units internal battery cool for 3
minutes before making another attempt.
9. When the vehicle starts, turn the jump-starter off/
on switch to the off position.
10. Leave the vehicle’s engine running.
11. Disconnect the clamp connected to the engine
block or chassis first, followed by the clamp that
is connected to the battery.
Recharge this unit fully after each use.
Caution! To reduce the risk of property damage:
• Vehicles may have electrical and electronic systems
(e.g. engine management systems, mobile phones)
that may be damaged if subjected to high starting
voltages and voltage peaks. Before connecting the
appliance to the vehicle, read the vehicle’s owner’s
manual to confirm that external starting assistance
is allowed.
• If vehicle fails to start, turn off the ignition, turn
off the Jump-Starter Power Switch, disconnect the
jump-start system’s leads and contact a qualified
technician to investigate why the engine did not start.
Using the LED area light
• The LED area light on/off button turns the LED area
light on and off.
• Periodically press the battery power level button to
check battery status.
Make sure the area light is turned off when the unit is
being recharged or stored.
TROUBLESHOOTING
Unit will not
charge
• Make sure the power switch is
in the off position.
• Make sure the jack of the
mains charging adapter is
properly connected to both the
unit and a functioning mains
power socket.
Unit fails to
jump-start
• Make sure the jump-starter on/
off switch is in the on position.
• Make sure a proper polarity
cable connection has been
established.
• Check that the unit has a full
charge. Recharge the unit if
necessary.
LED Area
Light does
not come
on
• Make sure the LED area light
button is turned on.
• Check that unit has a full
charge. Recharge the unit if
necessary.
MAINTENANCE
This unit has been designed to operate over a long
period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning!
Before performing any maintenance or
cleaning of the unit, unplug it from the power supply.
• From time to time wipe the unit with a damp cloth.
Do not use any abrasive or solvent-based cleaner. Do
not immerse the unit in water.
• Clean the outside case of the jump starter with a soft
cloth and, if necessary, mild soap solution.
• Do not allow liquid to enter the unit’. Do not operate
when the battery charger is wet.
• Keep the cords loosely coiled during storage to
prevent damage to the cords.
PROTECTING THE ENVIRONMENT
Correct disposal of this product
This marking indicates that this product
should not be disposed with other
household waste throughout the EU. To
prevent possible harm to the environment
or human health from uncontrolled
waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return
your used device, please use the return and collection
systems or contact the retailer where the product
was purchased. They can take this product for
environmentally safe recycling.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the
demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at municipal
waste sites or by the retailer when you purchase a
new product.
TECHNICAL DATA
BDJS350AU
BDJS450AU
Battery Type
12V 9 Ah
Sealed lead
acid
12V 17 Ah
Sealed lead
acid
Output (instant)
350A
450A
Output (constant
for 5 seconds)
200A
300A
Mains charging adapter
Input
100-240V ac,
50/60Hz
100-240V ac,
50/60Hz
Output
14,5V dc
(750mA)
14,5V dc
(750mA)
WARRANTY
Our goods come with guarantees that cannot be
excluded under the Australian & New Zealand
Consumer Law. You are entitled to a replacement
or refund for a major failure and compensation
for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of
acceptable quality and the failure does not
amount to a major failure.
Baccus Worldwide LLC is confident of the quality of
its products and offers an outstanding warranty. This
warranty statement is in addition to and in no way
prejudices your statutory rights under the Australian &
New Zealand Consumer Law.
If a Baccus Worldwide LLC product becomes
defective due to faulty materials, workmanship or
lack of conformity, within 24 months from the date
of purchase, Baccus Worldwide LLC guarantees to
replace defective parts, repair products subjected to
fair wear and tear or replace such products to make
sure of the minimum inconvenience to the customer
unless:
• The product has been used for trade, professional or
hire purposes;
• The product has been subjected to misuse or
neglect;
• The product has sustained damage through foreign
objects, substances or accidents;
• Repairs have been attempted by persons other than
Baccus Worldwide LLC service staff.
To claim on this warranty, you will need to submit
proof of purchase and return the allegedly defective
product to Baccus Worldwide LLC’s local market
distributer, at your expense.
Please visit our website www.baccusworldwide.com
to register your new Baccus Worldwide LLC product
and to be kept up to date on new products and special
offers. Further information on the Baccus Worldwide
LLC brand and our range of products is available at
www.baccusworldwide.com.
Distributed by:
Directed Electronics
Address:
44 Translink Drive, Keilor Park Victoria Australia 3042
PH:
+ 61 03 8331 4800
Email:
Baccus Worldwide LLC
Weena 290, 3012 NJ Rotterdam or
Postbus 819, 3000 AV Rotterdam
+31(0)10 282 16 11
BDJS350_450AU_Manual_091216.indd 6-7
9/12/2016 10:59:26 AM
