Black & Decker AS600, Оригинальное руководство пользователя

Страница: 7 / 72

7
ENGLISH
u
Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
u
Carefully follow all instructions and warnings on the
battery label and package.
u
Always place batteries correctly according to the polarity
(+ and -) as marked on the battery and the product.
u
Do not short-circuit the battery terminals.
u
Do not attempt to charge non-rechargeable batteries.
u
Do not mix old and new batteries. Replace all of them at
the same time with new batteries of the same brand and
type.
u
Keep batteries out of reach of children.
u
Remove batteries if the product will not be used for
several months.
u
Never attempt to open for any reason.
u
Do not store in locations where the temperature may
exceed 40 °C.
u
When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
u
Do not incinerate the batteries.
Features
1. On/off switch (forward)
2. On/off switch (reverse)
3. Spindle lock collar
4. Bit holder
5. Battery holder
Assembly
Warning! Before assembly, engage the spindle lock as
described below.
Fitting and removing a screwdriver bit (fig. A)
u
To fit a screwdriver bit (6), push it into the bit holder until it
locates.
u
To remove a screwdriver bit, pull it straight from the bit
holder.
Fitting and removing batteries (fig. B)
This tool uses 4 alkaline batteries (size AA).
Note: For optimum performance, we recommend only to use
batteries from a known brand.
Fitting
u
Keeping the tabs (7) depressed, pull the battery holder (5)
out of the tool.
u
Insert the batteries into the battery holder, orientating the
plus terminal (+) of each battery as shown on the battery
holder.
u
Insert the battery holder into the tool and push until it
clicks into place.
Removing
u
Keeping the tabs (7) depressed, pull the battery holder (5)
out of the tool.
u
Take the batteries from the battery holder.
Use
Warning! Let the tool work at its own pace. Do not overload.
Manual spindle lock (fig. C)
The manual spindle lock allows you to use the tool as a
regular manual screwdriver. You can give an extra twist to
firmly tighten a screw or to loosen a very tight screw.
u
To activate the spindle lock, turn the collar (3) to the
symbol.
u
To release the spindle lock, turn the collar (3) to the
symbol.
Operating the tool (fig. D)
u
Make sure that the spindle lock is released.
u
To tighten a screw or nut, keep the on/off switch (1)
depressed.
u
To loosen a screw or nut, keep the on/off switch (2)
depressed.
u
To switch the tool off, release the on/off switch.
Hints for optimum use
u
Always use the correct type and size of screwdriver bit.
u
If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
u
Use the spindle lock to loosen very tight screws or to
firmly tighten screws.
u
Always hold the tool and screwdriver bit in a straight line
with the screw.
u
When screwing in wood, it is recommended to drill a pilot
hole with a depth equal to the length of the screw. A pilot
hole guides the screw and prevents splintering or
distortion of the wood. For the optimum size of the pilot
hole, refer to the table below.
u
When screwing in hardwood, also drill a clearance hole
with a depth equal to half the length of the screw. For the
optimum size of the clearance hole, refer to the table
below.
Screw size Pilot hole ø Pilot hole ø Clearance
(softwood) (hardwood) hole
No. 6 (3.5 mm) 2.0 mm 2.5 mm 4 mm
No. 8 (4 mm) 3.2 mm 3.5 mm 5.0 mm
No. 10 (5 mm) 3.5 mm 4.0 mm 5.7 mm