Black & Decker Alligator GK1000-XE, Руководство пользователя

Страница: 7 / 12

7
Additional safety instructions for the Alligator
TM
Lopper
Warning! Never use the tool above shoulder height. Always
position yourself out of the path of falling branches and debris.
Warning! Do not use this tool to fell trees.
Keep all parts of your body and clothing away from the saw
chain at all times. Hold the tool in front of you and be aware
of the saw chain position especially when cutting branches
near the ground. Before you switch on make sure the saw
chain is not contacting anything.
Pre-plan a safe exit from falling branches and debris.
Ensure the exit route is clear of obstacles that would
prevent or hinder movement. Remember wet grass and
freshly cut bark is slippery.
Be aware of the direction that a branch may fall. Consider
all conditions that may affect the direction of fall, including:
- The intended direction of fall.
- The natural lean of the branch.
- Any unusual heavy limb structure or decay.
- Surrounding trees and obstacles including overhead
lines.
- The wind speed and direction.
The safe distance between a branch and debris to be felled
and bystanders, buildings and other objects is at least
2 1/2 times the length of the branch. Any bystander,
building or object within this distance is at risk from being
struck by the falling branch.
When cutting a limb that is under tension, be aware of
spring-back. When the tension in the wood fibres are
released the spring loaded limb may strike the operator
and/or throw the tool out of control.
Begin and continue cutting only with the chain moving at
full speed.
Watch for shifting branches or other forces that could close
a cut and pinch or fall into the chain.
Use extreme caution when re-entering a previous cut.
Engage spikes on lower jaw into wood and allow the chain
to reach full speed before proceeding with cut.
Use of this tool for operation different to those intended
could result in hazardous situations. Cut wood only. Don't
use this tool for purposes not intended - for example - Don't
use tool for cutting plastic, masonry or non wood building
materials.
If any debris gets caught with the guard or tool discontinue
use, disconnect the power cord and clear debris.
Worn chains and chain guide bars should be replaced.
Only use replacement bars and chains specified by the
manufacturer.
The following warning symbols are found on your tool:
Do not use your saw in wet conditions or expose it
to rain.
Always wear head, hearing and eye protection.
Beware of falling objects.
Keep bystanders away.
Do not use on ladders.
Do not dispose of product in bin.
:
To reduce the risk of injury, user
must read the instruction manual.
Do not let the moving chain contact any object at the tip of
the guide bar.
Keep your saw chain properly tensioned. Check tension at
regular intervals with the motor stopped and cord
disconnected.
Keep handles dry, clean and free from oil and grease.
Greasy oily handles are slippery causing loss of control.
Do not attempt to operate the tool when in a tree, on a
ladder or standing on any other unstable support.
Keep proper footing and balance at all times.
Hold the tool firmly with both hands when the motor is
running.
Always wear suitable safety equipment such as non-skid
safety shoes, hard hat, goggles, ear protection and gloves
when operating the tool.
Ensure someone is nearby (at a safe distance) in case of an
accident.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Service
a.
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
b. Power to the tool should always be supplied via residual
current device with a rated residual current of 30mA or
less.