5
NOTE:
Some battery manufacturers mark only the plus (+) ends of
the batteries. In these cases, the unmarked end of the battery
is the (-) end. Install the batteries as indicated and reinstall the
cap.
The end cap and battery holder assembly will only fit back into
the tool one way. If it does no seem to fit properly, don't force
it. Rotate it one half way around and try it again. When it is in
all the way, ensure that the two tabs snap into place.
IMPORTANT:
Incorrectly installed bat teries will reduce the tool's
performance or prevent its operation entirely. If your batteries
are fresh and you feel the tool lacks power or doesn't run,
double check the battery holder to see if the batteries are
installed properly (+ and - signs aligned as shown.) If proper
installation and fresh batteries do not yield satisfactory
performance, take or send the tool to your local Black &
Decker Service Center for a thorough inspection.
Be careful when storing the tool so that the switch is not
inadvertently depressed by some object. This would, of
course, deplete the batteries in just a short while.
OPERATING INSTRUCTIONS
INSERTING AN ACCESSORY (FIGURE D)
◆
Hold the unit in one hand.
◆
Pull the sleeve (4) back.
◆
Insert the shank of the accessory (6) into the holder.
◆
Release the sleeve.
MANUAL SPINDLE LOCK (FIGURE E)
The manual spindle lock allows you to use the tool as a
regular manual screwdriver. You can give an extra twist to
firmly tighten a screw or to loosen a very tight screw.
◆
To activate the spindle lock, turn the collar (3) to show the
LOCK
symbol.
◆
To release the spindle lock, turn the collar (3) to show the
POWER
symbol.
NOTE:
Do not attempt to operate the tool when the spindle
lock is activated.
OPERATING THE TOOL (FIGURE A)
◆
Make sure that the spindle lock is released.
◆
To tighten a screw or nut, keep the on/off switch (1)
depressed.
◆
To loosen a screw or nut, keep the on/off switch (2)
depressed.
◆
To switch the tool off, release the on/off switch.
Hints for optimum use
◆
Always use the correct type of screwdriver bit or drill bit.
◆
If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
◆
Use the spindle lock to loosen very tight screws or to
firmly tighten screws.
◆
Always hold the tool and screwdriver bit in a straight line
with the screw.
◆
Do not use drill bits with a diameter larger than 1/4 inch.
◆
When drilling in plasterboard, use a 3/16 inch drill bit for
the supplied plugs.
◆
When screwing in wood, drill a 1/8 inch pilot hole for the
supplied screws. A pilot hole guides the screw and
prevents splintering or distortion of the wood.
Maintenance
Your Black & Decker tool has been designed to operate over a
long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning!
Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
◆
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
◆
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Содержание AD600-XE
Страница 1: ...AD600 XE Australia New Zealand www blackanddecker com au ...
Страница 2: ...2 5 7 Position Instructions C 3 E B A 6 4 D 5 2 1 3 4 ...
Страница 7: ...7 ...