background image

13

E N G L I S H

Keep handles and switches dry, clean and free
from oil and grease.

20.Repairs

This tool complies with relevant safety
requirements. Repairs should only be carried
out by qualified persons using original spare
parts; otherwise this may result in considerable
danger to the user.

Additional safety instructions for angle grinders

Wear safety glasses or goggles when
operating this tool.

Wear ear protection when operating this
tool.

Wear gloves when operating this tool.

Do not cut or grind light metal with a
magnesium content exceeding 80%,
since this type of metal is flammable.

Only use grinding and cutting discs and other
accessories recommended in this manual.
Make sure that the maximum speed of the
grinding or cutting disc exceeds the no-load
speed of the tool.
Do not cut workpieces requiring a maximum
depth of cut exceeding that of the cutting disc.
Never use the tool without the guard, except
for sanding.
Do not exert side pressure on the grinding or
cutting disc.
Use this tool only as a hand held tool.

Sanding

Wear a dust mask whenever sanding.
Thoroughly remove all dust after sanding.
Take special care when sanding paint which is
possibly lead based or when sanding some
woods and metal which may produce toxic dust:
- Wear a dust mask specifically designed for

protection against lead paint dust and fumes
and ensure that persons within or entering
the work area are also protected.

- Do not let children or pregnant women enter

the work area.

- Do not eat, drink or smoke in the work area.
- Dispose of dust particles and any other

debris safely.

ELECTRICAL SAFETY

The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.

This tool is double insulated in accordance
with EN 50144; therefore no earth wire is
required.

Using an extension cable

Always use an approved extension cable suitable
for the power input of this tool (see technical
data).  Before use, inspect the extension cable for
signs of damage, wear and ageing.  Replace the
extension cable if damaged or defective.
When using a cable reel, always unwind the cable
completely. Use of an extension cable not suitable
for the power input of the tool or which is damaged
or defective may result in a risk of fire and electric
shock.

PACKAGE CONTENTS

The package contains:
1 Angle grinder
1 Side handle
1 Grinding or cutting disc
1 Flange set
1 Two-pin spanner
1 Instruction manual

Carefully unpack all parts.

OVERVIEW (fig. A)

1. On/off switch
2. Side handle
3. Spindle lock

4. Guard
5. Grinding or cutting disc

Содержание 478306-00

















Отзывы: