manualshive.com logo in svg

BKI LGF, Руководство по обслуживанию

Поделиться
Скачать
BKI LGF Скачать руководство пользователя страница 5

Gas Pressure Fryer 

 

Introduction 

 

 

3 

Specific Precautions 

 

Lids for LGF Pressure Fryers

 

manufactured prior to May 27, 1980 (or units with 

serial numbers lower than 3613) could be manually opened while under pressure 
resulting in serious injury or death. If you have one of these units, please contact 
the BKI

 

Technical Services Department toll-free at 1-800-927-6887 for urgent 

update information. 

 

Risk of fire exists if the oil level drops below 5mm of the maximum oil level. 

 

Use of oil/shortening older than the manufacturers recommendations for life of 
the oil is prone to surge boiling and flash fires.  Follow the oil manufacturers 
guidelines for the life cycle of oil/shortening. 

 

Do not open the drain valve or the fill valve while the fryer is under pressure.  
Serious burns may result. 

 

Follow instructions regarding effects of surge boiling of over-wet foods and 
proper load size. 

 

This unit incorporates components that contain Mercury. The use of Mercury 
relays is an industry standard. 

 

Equipotential ground plane

 

When a high current flows through a conductor, differences in potential appear 
between the conductor and nearby metallic surfaces near the appliance.  As a 
result, sparks may be produced between the appliance and surrounding metal 
surfaces.  These sparks could cause serious injury, damage, or fire. 
 
BKI provides an Equipotential ground terminal for the connection of a bonding 
conductor after the installation of the appliance per lEC60417-1.  This terminal is 
located on the inside of the Power Entry Supply box near the Earth connection 
and is marked with this symbol. 
 

 

 

Full Disconnection 

In accordance with Local and/or National wiring codes, the installer must provide 
a means of full disconnection under over voltage Category III conditions.  An IEC 
approved cord and plug combination will meet this requirement. 
 
Units not provided with a cord and plug do not meet this requirement. In 
accordance with Local and/or National wiring codes, the installer must provide 
the means of full disconnection. 

 

The fryer is designed to hold a maximum of 35lbs (15.9KG) of oil/shortening. 

 

Содержание LGF





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды