manualshive.com logo in svg

BK Radio GPH Flex Mode, Руководство пользователя

Поделиться
Скачать
BK Radio GPH Flex Mode Скачать руководство пользователя страница 25

26

 

 

BK Radio

 

9.

 

P

RESS THE 

*

 KEY

 on the master radio 

keypad. The display will flash “

PROG

”

 

signifying that the radio is ready to 
download its program to the clone. 

10.

  P

RESS THE 

FCN

 KEY

 on the master radio 

keypad. The program in the master will 
then be downloaded to the clone. The clone 
will automatically send back the program to 
the master to verify a successful cloning. 

11.

  I

F THE DOWNLOAD WAS SUCCESSFUL

, the 

display on the master will resume flashing 
“

PROG

”

. 

•  To clone the other channel group, turn 

off both radios and go back to Step 3 on 
the previous page, changing the channel 
group as required. 

•  If cloning is finished, turn off the clone 

and disconnect the cloning cable. 
Normal radio operation will occur when 
you turn on the clone.    

12.

  I

F THE DOWNLOAD WAS NOT SUCCESSFUL

, 

the master will display “

FAIL

”

 and multiple 

beeps will follow. Failure of downloading 
can be due to: 

• Improper 

connection 

•  Failure to turn on the clone 

•  Setting the clone in programming mode 

NOTE:

  To stop the “

FAIL

”

 mode, press 

CLR

, 

turn off both radios, and try again, 
starting with Step 1 on the previous 
page.

 

  PRG 

            

P R O G 

 

1

 

2

 

3

 

4

 

5

 

6

 

7

 

8

 

9

 

0

 

*

 

#

 

CLR

 

FCN

 

PRI

 

ENT

 

 

1

 

2

 

3

 

4

 

5

 

6

 

7

 

8

 

9

 

0

 

*

 

#

 

CLR

 

FCN

 

PRI

 

ENT

 

 

 PRG 

       F  A  I  L 

Содержание GPH Flex Mode






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды