BK Precision XLS200 MKII Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 9

BK Precision XLS200 MKII Скачать руководство пользователя страница 9

(7)

SPECIFICATION

System Type:

Drive Units:

Amplifier:

Inputs:

Nominal impedance/input voltage:

Sensitivity/Features:

Dimensions HxWxD:

Weight each unpacked:

Color finishes:

Quiescent Power Consumption:

Infinite Baffle Sub-bass system with on-board amplification and active
filtering. Fully optimised enclosure manufactured from critically damped
18mm and 25mm MDF

250mm 10“ high-efficiency unit. Extreme long stroke composite fiber
cone driven by a 2 ” 50mm voice coil. Heavy-duty non-resonant cast
aluminium chassis and fully optimised stacked magnet system.

275W RMS DC coupled bi-polar.

High Level 100K ohm unbalanced via Neutrik Speakon connector
Low level 10K unbalanced via gold plated RCA connectors.

110/120v (220/240v) where applicable.

Phase control 0 and 180 Deg.
High and low level mixing capability.
Automatic Speaker Protection

XLS200

390D x 295H x 295W / 15.35“ x 11.61” x 11.61”

XLS200-DF

345D x 355H x 295W / 13.58“ x 13.98” x 11.61”

17.5Kg - 38.5 lbs.

Cherry ,Light Oak, Black and Silver

14 W

«
...
7
8
9

Содержание XLS200 MKII










Отзывы:

Нет отзывов