BK Precision P12-300 Скачать руководство пользователя страница 9

(7)

SPECIFICATION

System Type:

Drive Units:

Auto On

Amplifier:

Inputs:

 

Nominal impedance/input voltage:

Sensitivity/Features:

Dimensions HxWxD:

Weight each unpacked:

Color finishes:

Standby Power Consumption:

Sealed system with a   long throw low resonance drive unit finely tuned 
with Linkwitz Riley Correction

300mm 12“ high-efficiency unit. Extreme long stroke composite fiber 
cone driven by a 2 ” 50mm voice coil. Heavy-duty non-resonant cast 
aluminium chassis and fully optimised stacked magnet system.

Switches off after 10 minutes without signal

300W RMS  DC coupled bi-polar.

High Level 100K ohm unbalanced via Neutrik Speakon connector
Low level 10K unbalanced via gold plated RCA connectors.

110/120v (220/240v) where applicable.

Phase control 0 and 180 Deg. 
High and low level mixing capability. 
Automatic Speaker Protection

400D x 400H x 450W

30Kg - 46.2 lbs.

Cherry ,Light Oak, Black and Silver

1 W

This product is subject to Directive 2002/96/EC of the European Parliament and the Council of the European 
Union on Waste of Electrical and Electronic Equipment (WEEE) and, in jurisdictions adopting that Directive, is 
marked as being put on the market after August 13, 2005, and should not be disposed of as unsorted 
municipal/public waste. Please utilise your local WEEE collection facilities in the disposition and otherwise 
observe all applicable requirements. 

WEEE Consumer Notice

Please be AWARE

When BK design a subwoofer it is built to withstand a certain amount of excessive use, to this end we 
design in circuits that will help protect the drive unit and amplifier from damage. That said these circuits do 
have a limit and therefore can be over-driven if the user insists on turning up either the drive level from the 
source, or the gain controls on the subwoofer. When the subwoofer is over-driven it will sound distorted 
and if pushed extremely hard may emit a cracking noise. If this happens then please turn the gain down   
from your source. Prolonged misuse in this fashion will damage the subwoofer, such damage is not 
covered by warranty

It   is worth remembering   that a subwoofer is there to augment your sound system and not to overwhelm   
it. If you feel that there is not enough bass then there may be room   issues that could easily be overcome 
by a different room   placement. It could also mean you simply have too small a sub for your room or taste.

Содержание P12-300










Отзывы: