manualshive.com logo in svg

BK Precision 9130B, Руководство пользователя, Страница: 33 / 50

Поделиться
Скачать
BK Precision 9130B Скачать руководство пользователя страница 33

 

22 

 

 

CH2 

Configure channel 2 

 

CH3 

Configure channel 3 

Comb 

 

 

 

Off 

Turns off series, parallel, or tracking mode 

 

Series 

Configure series mode 

 

Para 

Configure parallel mode 

 

Track 

Configure tracking mode 

Exit 

 

Move up menu structure 

 

 

 

4.3

 

Output Power-on State 

The initial power-on state of the power supply outputs can be configured. 

1.

 

From the Config menu, select OutState and press the 

button. 

2.

 

There are two options that can be selected using the 

keys or rotary knob: 

3.

 

OFF – Default output state. 

4.

 

Last – Last output state during the last power-off. 

5.

 

Select OFF or Last and press the 

button. 

6.

 

To exit the menu at any time, press 

 twice. 

 

4.4

 

Output Parameters 

This option sets the voltage and current output state values at power-on. 

1.

 

From the Config menu, select OutParam and press the 

button.  

2.

 

There are two options that can be selected using the 

 curser keys or rotary 

knob: 

3.

 

Reset – Restores the default voltage, current, and output states based on factory default 

parameters.  

Keep –  Restores the voltage, current, and output states for each channel based on the 

settings during last power-off. 

4.

 

Select the desired settings for power-on, and press the 

 button to save changes. 

5.

 

To exit the menu at any time, press the 

 key twice. 

 

4.5

 

Lock/Unlock Rotary Knob 

This option enables or disables the rotary knob. 

1.

 

From the Config menu, select Knob and press the 

 button. 

2.

 

There are two options that can be selected by using the 

 keys or rotary knob: 

Unlock – Enable rotary knob 

www.

GlobalTestSupply

.com

Quality BK Precision Products Online at:

[email protected]

Содержание 9130B



















































Отзывы:

Нет отзывов