BJM Pumps J08 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 41

BJM Pumps J08 Скачать руководство пользователя страница 5

6

INSPECTION

Review all safety information before servicing pump.

The following are recommended installation practices/procedures for the pump. If there
are questions in regards to your specific application, contact your local

BJM Pumps

distributor or BJM Pumps, LLC.

PRE-INSTALLATION INSPECTION

1)  Check the pump for damage that may have occurred during shipment.
2)  Inspect the pump for any cracks, dents, damaged threads, etc.
3)  Check power cord (and Seal Minder® cord, if installed) for any cuts or damage.
4)  Check for, and tighten any hardware that appears loose.
5)  Carefully read all tags, decals and markings on the pump.

If anything appears to be abnormal, contact your

BJM Pumps

distributor or BJM

Pumps, LLC. If damaged, the pump may need to be repaired before use. Do not install
or use the pump until appropriate action has been taken.

Lubrication:

No additional lubrication is necessary. The shaft seal and bearings are fully lubricated
from the factory. Seal oil should be checked once per year. See table below.

«
...
3
4
5
6
7
...
»

Содержание J08










































Отзывы:

Нет отзывов