BIXOLON SRP-330II Скачать руководство пользователя

Страница: 103 / 125

SRP-330II/332II

Rev. 1.00

BIXOLON

- 103 -

GS L

Function:

Set left margin

Code:

ASCII

Hex

Decimal

Range:

0 ≤ nL ≤ 255, 0 ≤ nH ≤ 255

Default:

(nL + nH x 256)=0 (nL=0, nH=0)

Description:

This command sets the left margin specified to [(nL + nH x 256) x (horizontal motion units)].

Remarks:

■

The left margin is not effective in page mode. If the left margin is enabled in page mode, the setting is available when

the printer returns to standard mode.

■

When the setting is beyond the printable area, the left margin is automatically set to the maximum value of the

printable area.

■

Since the left margin is the same as the leftmost side of the printable area, the left side of the printable area is

changed according to the left margin specified.

■

The setting of this command remains effective until ESC @, printer reset or power cycling is executed.

Printable area

Left margin

Printing area width

Differences:

None

Содержание SRP-330II






























































































































Результаты поиска

Содержание SRP-330II

Отзывы:

Похожие инструкции для SRP-330II

Бренды по названию

Популярные бренды

BIXOLON SRP-330II, Руководство по управлению

Результаты поиска

Содержание SRP-330II

Отзывы:

Похожие инструкции для SRP-330II

Бренды по названию

Популярные бренды