background image

Repeat cleaning passes until solution being pulled up 
appears clean.

Continue passes without pressing the trigger until you 
can’t see any more water being pulled up. 

Note: Both the SmartMix Bottle and the clean 

water Tank must have liquid in them in 
order for the machine to spray. If one is 
empty, the machine will temporarily lose 
prime and will not spray cleaning solution 
or water.

After cleaning, you may want to turn the SmartMix Dial 
to the 

Water Rinse

 setting to give your carpeting a final 

rinse. This will ensure thorough removal of embedded 
dirt loosened by the BISSELL Advanced Deep Cleaning 
Formula. BISSELL Advanced Deep Cleaning Formulas 
contain an anti-resoiling agent that helps your carpets 
repel dirt and keeps them looking good longer. 

When the cleaning job is complete refer to the 

Maintenance

 section on pages 15-16 for machine 

cleanup and storage instructions

.

Note: You may notice hair and debris deposits 

on the carpet that were loosened by the 
brushing action (especially with newer 
carpets that have never been deep cleaned 
before). This debris should be picked up 
and thrown away. Debris that deposits in 
the Brush Belt should be cleaned between 
uses to keep the Belts running free.

 

Do Not Delay! 

Failure to attend to an accident soon after it occurs 

may cause it to set and become permanent.

Before treating any stain, follow these pretreatment steps:

Blot up liquids with an absorbent cloth or paper towels. 
White materials are recommended because certain dyes 
may bleed and make the stain worse. 

Gently scrape up semi-solids with a spoon or spatula. 
Do not use a knife or other utensil with sharp edges 
because it could damage the carpet or upholstery.

If the area has dried, remove the remaining semi-solids 
and residue with a sweeper or vacuum. 

Be sure to pre-test any spot removal solutions or chemicals 
on an inconspicuous area first. This is extremely 
important; different dyes and materials could be damaged 
or discoloured by a cleaning solution. If such a change 
should occur, try a different solution or call a professional. If 
cleaning on Berber Carpet gently run your machine over 
a hidden area. If no fuzzing occurs, continue cleaning in 
soiled area.

12

Stain Removal 

3.

4.

2.

1.

Carpet Cleaning Continued

4.

5.

6.

7.

Содержание PROHEAT II





















Отзывы: