www.BISSELL.ca
5
A
Product View
disconnect from the electrical outlet. Hold
the plug and press the automatic cord rewind
button to rewind the cord automatically.
C2 - Power button
Turn the power ON or OFF by pressing lightly
downward on the power button ( ).
Special tools
Your BISSELL vacuum is not only a powerful
carpet and rug vacuum cleaner, it’s also a
versatile bare floor and above floor vacuum
cleaner when you select one of the special
tools.
Motorized powerhead (7)
Turn the power brush ON by pressing the
power button ( ) on the handle. Turn the
power brush OFF by pressing the power
button ( ) again.
NOTE: The power brush will automatically
turn off if the rotator bar is blocked by
clogs (hair, cloth, etc.) for your protection.
In that case, turn off the power head,
unplug the vacuum, clean the clog, and
re-start the power brush.
Small accessories (13)
Use the crevice tool in tight, narrow spaces.
Use the dusting brush to clean curtains,
draperies, and side tables and window
ledges. Use upholstery tool for soft
furnishings.
Air flow regulator (3)
Open the air flow regulator by sliding the
regulator up towards the handle to an open
position. This will reduce the suction power
for vacuuming delicate fabrics.
For full suction power, close the air flow
regulator by sliding the regulator down to
the closed position.
Thermal protector
An internal thermal protector has been
designed into your vacuum to protect it from
overheating. When the thermal protector
activates, the vacuum motor will stop
operating. If this happens:
1.
Turn the cleaner OFF and unplug from
electrical outlet.
2.
Empty dirt container, check filters and air
passages for dirt accumulation.
3.
Leave vacuum unplugged. The thermal
protector automatically resets after
approximately 2 hours then plug vacuum in
and turn ON. If the thermal protector does
not reset, call BISSELL Consumer Care or
visit the website.
B
Assembly
1.
Connect the hose to the vacuum by inserting
the hose connector into the suction opening on
the bottom front of the vacuum. Push in until it
clicks into the locked position.
2.
Connect the telescoping extension wand to
the handle end of the hose.
3.
Connect the powerhead onto the telescoping
extension wand
4.
To extend the telescoping extension wand,
grab the height adjustment collar while holding
the handle and extend up or down to the
desired length.
Colours may vary from models shown.
C
Operations
Power cord
The power cord is located at the rear of the
vacuum. Gently pull out the power cord,
watching for the yellow line. Stop pulling the
power cord once the yellow line is visible.
There is also a red line, which indicates the
end of the usable cord. Do not pull the
power cord out beyond the red line.
C1 - Automatic cord rewind
Your vacuum is equipped with an automatic
cord rewind. When cleaning is finished, press
the power button OFF and grasp the plug to
Do not plug in your cleaner until you have
completely assembled it per the following
instructions and are familiar with all instructions
and operating procedures.
Be careful to avoid injury as cord retracts very quickly.
Plastic film can be dangerous. To avoid danger of
suffocation, keep away from babies and children.
Before using your vacuum, make sure that the dirt
cup and all filters are in place. Do not operate your
vacuum without the dirt cup and filters.
1 Handle
2 Brush On/Off
3 Variable Suction Control
4 Hose Release Button
5 Height Adjustable Collar
6 PowerFoot Release Button
7 PowerFoot
8 Hose
9 Dirt Cup Release Latch
10 Filter Cup Release Latch
11 Easy Empty™ Dirt Cup
12 Hose Connector
13 Crevice Tool, Dusting Brush &
Upholstery TooL
4
www.BISSELL.ca
A
D1
C2
D3
D2
D4
1.
3.
2.
3.
1.
2.
3.
4.
2.
3.
2.
1
2
3
4
5
6
10
8
9
7
11
12
13
B
C1
1.
3.
2.
Содержание POWERGROOM MultiCyclonic 1654 Series
Страница 1: ...POWERGROOM MultiCyclonic 1654 SERIES...
