background image

12

Troubleshooting

Vacuum cleaner won’t run

Possible Causes

 

Remedies

 

Power cord not plugged in 

  Check electrical plug

 

Blown fuse/tripped breaker 

  Check/Replace fuse or 

  

 reset 

breaker

Vacuum cleaner won’t pick up dirt

Possible Causes

 

Remedies

 

Incorrect Height Adjustment 

  Adjust Powerfoot to correct 

  

 height 

setting

 

Hose not attached to suction opening 

  Grasp Quick Reach Handle and 

 

 

  firmly push Hose Wand onto the 

  

 suction 

opening

 

Twist ‘n Snap Hose not securely attached. 

  Make sure Twist ‘n Snap Hose is 

 

 

  snapped into locked position

 

Crack or hole in Hose 

  Check Hose and replace if needed

 

Broken or worn Drive Belt 

  Replace Drive Belt, see pg. 9-10

 

Rotating Floor Brush bristles worn 

  Replace brush

 

Rotating Floor Brush jammed 

  Remove brush and clean debris from 

  

 brush 

ends

 

Clog in vacuum 

  Clear clog, see pg. 11-12 

 

Dirt Container full 

  Empty Dirt Container

1

1

2

2

1

1

2

2

3

3

4

4

5

5

 WARNING: 

To reduce the risk of injury from moving 
parts and/ or electrical shock, turn Power 
Switch OFF and disconnect polarized plug 
from electrical outlet before performing 
troubleshooting checks.

5.

6.

Suction Inlet

Air Passageway

Louvers

Hose Wand Base

Check Upper Tank and Louvers for build up or clogs.  
Check to make sure Louvers are installed correctly. To 
unlock the Louvers, grasp the rim and turn toward the left. 
Pull straight down to remove. If the Louvers are 
missing or not locked into place, check and clear the tube 
in the center of the Dirt Container.

Remove the Twist ‘n Snap Hose from the vacuum by 
turning to the left. Check the Suction Inlet, Hose and Hose 
Wand for clogs. Remove any clogs from the hose using a 
long, narrow object.

Check the Foot Hose for clogs. If needed, remove the screw 
attaching the Hose Wand Base to the vacuum. Straighten 
the Foot Hose and unclog with a long, narrow object.

If the clog persists, follow the instructions for Checking 
the Rotating Floor Brush on page 9-10 and inspect the Air 
Passageway for obstructions.

3.

4.

Clearing Clogs Continued

6

6

7

7

8

8

9

9

ug603-2559_3574-3576_1005.indd   12

ug603-2559_3574-3576_1005.indd   12

1/4/06   9:45:59 AM

1/4/06   9:45:59 AM

Содержание 20Q9

















Отзывы: