1
——
Instruction Manual ——
Competition Portable Tennis System
TN10P
P A R T S L I S T
Item
Qty
Description
Item
Qty
Description
A
1
Winch Post
L
2
1/2”
Lock Nut
B
1
Non
-
Winch Post
M
4
Connecting Bar
C
1
Removable Winch Handle
N
16
3/8”
X
1”
Hex Bolt
D
1
TN10NP Tennis Net
O
2
5/16”
X
1”
Carriage Bolt
E
3
Spreader Tube
P
2
5/16”
Flat Washer
F
4
Inner Tube
Q
2
5/16”
Lock Washer
G
2
Stabilizer Leg
R
2
5/16”
Hex Nut
H
2
Clamp
S
1
TN10P Center Strap Anchor
I
8
5/16”
X
3/4”
Button Head Bolt
T
1
TN10CS Center Court Hold Down Strap
J
4
Wheel
U
2
Lacing Cord
K
2
1/2”
X 7
1/2”
Hex Bolt
Date: 3/13/20 Rev: 1 B.A. N.J.C. File: \pub\TN10P Ref#: 960941
Inspect all contents prior to installation. Report any missing parts to dealer immediately
.
Read all instructions before proceeding.
1.
Slide the
Connecting Bar
(M) into the
Inner Tube
(F) through the channel so that all the holes are lined up
as shown. Insert the inner tube assembly into either the
Winch Post
(A) or the
Non Winch Post
(B) leaving
six holes exposed for the
Spreader Tube
(E) attachment. Using two of the
3/8”
X
1”
Hex Bolts
(N) loosely
attach the inner tube assembly to the
Winch Post
(A). Slide a
Spreader Tube
(E) over the exposed portion
of the inner tube assembly and attach it using two more
3/8”
X
1”
Hex Bolts
(N). Continue the same
process with two more
Spreader Tubes
(E) followed by the
Non Winch Post
(B). Tighten all of the
3/8”
X
1”
Hex Bolts
(N). See Figures 1 & 7.
2.
Loosen the set screws that secure the lacing bars to the
Winch Post
(A) and the
Non Winch Post
(B). Slide
the lacing bar up, then using the
5/16”
X
3/4”
Button Head Bolts
(I) attach the
Clamp
(H) to the
Stabilizer
Leg
(G) Assembly. Leave the
5/16”
X
3/4”
Button Head Bolts
(I) hand tight. Slide the lacing bar back in
its original position and tighten the set screw. See Figure 2.
3.
Remove one of the
3/8”
X
1”
Hex Bolts
(N) on the middle
Spreader Tube
(E). Slide the
5/16”
X
1”
Carriage Bolts
(O) down the groove in the
Spreader Tube
(E) towards the middle. Replace
3/8”
X
1”
Hex
Bolt (N). Measure approximately 77
7/8”
from the end of the middle
Spreader Tube
(E) and make a small
mark. Place the
TN10P Center Strap Anchor
(S) over the
5/16”
X
1”
Carriage Bolts
(O). Line the edge of
the
TN10P Center Strap Anchor
(S) up with the mark made earlier. Tighten it down to the
Spreader Tube
(E) using the
5/16”
Flat Washers
(P),
5/16”
Lock Washers
(Q), and the
5/16”
Hex Nuts
(R).
See Figures 3 & 4.
