Bishamon NSA3500N Скачать руководство пользователя страница 1

Страница: 1 / 40

Dear users

Thank you for purchasing our Bishamon 2 Posts Lift. Before using the lift, read through and be

familiar with this manual. Fully understand the precautions, directions, and other information

contained in this manual to ensure correct use. Failure to do so may result not only in insufficient

performance of the lift but also in falling of the vehicle or a personal accident.

Keep this manual in a safe place for future reference. In case of loss, immediately request a new

copy.

If the product is supplied with a wrong manual, contact your dealer for a correct copy.

Perform periodic maintenance inspections of the lift to ensure safe work with the lift and to keep the

lift fully functional.

Operation and Service Manual

NSA3500N
NSA3500NH
OSA3500N
OSA3500NH

About maintenance inspection

16.04

2 POSTS LIFT

Содержание NSA3500N









































Результаты поиска

Содержание NSA3500N

Отзывы:

Похожие инструкции для NSA3500N

Бренды по названию

Популярные бренды

Bishamon NSA3500N, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание NSA3500N

Отзывы:

Похожие инструкции для NSA3500N

Бренды по названию

Популярные бренды