manualshive.com logo in svg

BIRD TERMALINE 8201, Руководство по эксплуатации

Поделиться
Скачать
BIRD TERMALINE 8201 Скачать руководство пользователя страница 21

Maintenance

12

Storage

No special preparations are needed for storage other than to cover the 
equipment to keep out dust and dirt. Store the unit in a clean dry environment 
where the ambient temperature will remain within the approximate working 
range of the instrument -40°C to +45°C (-40°F to +113°F) for Model 8201 and -
40°C to +30°C (-40°F to +86°F) for Model 8203.

Customer Service

Any maintenance or service procedure beyond the scope of those in this 
chapter should be referred to a qualified service center.

If the unit needs to be returned for any reason, request an Return Material 
Authorization (RMA) through the Bird Technologies website. All instruments 
returned must be shipped prepaid and to the attention of the RMA number.

Bird Service Center 

30303 Aurora Road 
Cleveland (Solon), Ohio 44139-2794 
Fax: (440) 248-5426 
E-mail: 

[email protected]

For the location of the Sales Office nearest you, visit our Web site at:

http://www.birdrf.com

Содержание TERMALINE 8201

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды