BIRD SiteHawk SK-200-TC Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 65

background image

38

Chapter 6

Data Save and Export

Saving and Recalling SiteHawk Status Data

SiteHawk status, calibration result, and tracing data can be saved to the
instrument, and can be recalled to be displayed on the sweep display area.

The parameters for this instrument setting include: scale, trace, cursor and
analysis. These parameters are saved in the status files.

CAUTION

Do not connect the unit to a PC USB port.

File transfer must be done using a USB Drive.

Trace Data in CSV File Format

SiteHawk can track data of a single trace and then save the data as a comma
separated values (CSV) file. The CSV file contains a list of data separated by
commas. The current format and response trajectory under the incentive value
is stored in the CSV file.

Trace data is saved in the following format to the *.CSV file:

F[n] = Frequency about point N.
Data1 = Trace response value, Real part
Data2 = 0,Imaginary part

Trace Data S1p File

SiteHawk can save the parameters to the S1p file. The S1p file contains the
frequency value and S-parameter. S1p files are used to store a single port
parameter. Only one path of data is saved to the file.

The file contains a comments, title and track data lines. Comments are indicated
using an exclamation "!" mark. Title of the start of the data is indicated using a
pound "#" sign with the data following.

«
...
45
46
47
48
49
...
»

Содержание SiteHawk SK-200-TC


































































Отзывы:

Нет отзывов

Похожие инструкции для SiteHawk SK-200-TC

Бренд: Panasonic Страницы: 180

SMatrix DMX2400

Бренд: dallmeier Страницы: 12

Бренд: E Instruments Страницы: 2

POCKET COLORIMETER II

Бренд: Hach Страницы: 188

Бренд: OHAUS Страницы: 32

Бренд: Raymarine Страницы: 42

Ultraprobe 9000

Бренд: UE Systems Страницы: 25

ULTRAPROBE 10000

Бренд: UE Systems Страницы: 6

Бренд: Vaisala Страницы: 2

Бренд: YOKOGAWA Страницы: 16

Electone Stagea ELS-01C

Бренд: Yamaha Страницы: 248

Бренд: X-laser Страницы: 17

Бренд: Garmin Страницы: 22

Бренд: Toro Страницы: 60

Ratio:Guard Advanced

Бренд: H.E. Anderson Страницы: 9

Бренд: Kawai Страницы: 72

Бренд: NIEUWKOOP Страницы: 2

Бренд: M-Audio Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды