BIOTRONIK Evia HF Скачать руководство пользователя страница 95

Страница: 95 / 138

Chapter 7

Other Functions/Features

Evia HF / HF-T Technical Manual

PAGE 87

7. Other Functions/Features

Evia HF / HF-T pulse generators offer many additional functions and features to assist the physician in

the care of the pacemaker patient.

7.1 Safe Program Settings

Activating the preset values for the Safe Program is a quick and convenient way to provide VVI

pacing at a high output setting in urgent situations.

Table 19

shows the Safe Program settings for

Evia CRT-P devices.

Parameter

Setting

Mode

VVI

Pacing Rate

70 ppm

Amplitude

4.8 V (Right/Left ventricle)

Pulse Width

1.0 ms (Right/Left ventricle

Sensitivity

2.5 mV

Ventricular Refractory

Period

300 ms (RV)

200 ms LV

Pacing Polarity

Unipolar

Single Chamber Hysteresis

OFF

Table 19: Safe Program Settings

7.2 Magnet Effect
7.2.1 Automatic Magnet Effect

After magnet application the pulse generator paces at 90 ppm for 10 cycles asynchronously. Thereafter,

the pulse generator paces synchronously at the programmed basic rate. During asynchronous pacing,

the AV interval is reduced to 100 ms.

7.2.2 Asynchronous Magnet Effect

When programmed to asynchronous operation, magnet application results in asynchronous pacing.

The pulse generator paces asynchronously at 90 ppm as long as the magnet is over the pulse

generator. Upon magnet removal, the current basic interval is completed before the pulse generator

reverts to its original operating mode.
If the magnet effect is set to asynchronous, the AV delay is reduced to 100 ms (or the programmed AV

delay, whichever is shorter). Shortening of the AV delay to 100 ms during asynchronous AV sequential

stimulation is provided to avoid ventricular fusion beats in the presence of intact AV conduction. This

allows efficient diagnosis of ventricular capture or failure to capture.

7.2.3 Synchronous Magnet Effect

If the magnet effect is programmed to synchronous operation, magnet application does not affect timing

and sensing behavior of the pulse generator. Synchronous operation is of particular importance during

follow-up, if sensing and inhibition functions are desired during magnet application.
Trend monitor and event counter operation is interrupted during any magnet application.

Содержание Evia HF











































































































































Результаты поиска

Содержание Evia HF

Отзывы:

BIOTRONIK Evia HF, Техническое руководство, Страница: 95 / 138

Результаты поиска

Содержание Evia HF

Отзывы: