BIOTRONIK Evia HF Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 138

BIOTRONIK Evia HF Скачать руководство пользователя страница 108

Chapter 10

Follow-up Procedures

Evia HF / HF-T Technical Manual

PAGE 100

As the threshold test begins, the selected pacing parameters are transmitted temporarily to the device.

These parameters are default parameters (i.e.: the parameters programmed between test parameters)

and should be adjusted to guarantee capture. The rate should be programmed above the patient’s

intrinsic rate to prevent inhibition. Thereafter, test amplitudes can be decremented until capture is

lost; and the threshold is determined. The test amplitude will change only when new amplitudes are

selected and the Number of Pulses is programmed to “∞”. Otherwise, a set number of pulses (1-10)

will be delivered with each new test amplitude before reverting back to the starting value. The default

parameters will be reprogrammed between test selections.
When each test is complete, the user is prompted to enter the threshold value, which is stored for future

reference. The ECG strip from the entire test is printed if Report is set to a user-defined printer speed.

Otherwise an annotated version of the test can be printed after the test by selecting the “Print” button,

which is found in the lower left corner of the screen.
To determine the threshold, the ECG or IEGM must be observed continuously. Based on the measured

threshold, the pulse amplitude for the permanent program should be adjusted. Please consult the

pertinent medical literature for specific recommendations regarding necessary safety margins.

10.4 P/R Measurement

The Evia CRT-P sensing test is the first test that appears when selecting the Tests button on the right

hand side of the programmer screen, shown in

. The Evia CRT-P provides multiple test

modes for sensing as shown in

. All bolded values can be changed by the user at any time.

When the Sensing test is started, the minimum, mean and maximum values of each chamber

measured by the device will be displayed. Typically, there should not be large variations between the

minimum, mean and maximum values. If large variations are seen, one should review the strip for

premature events (PVCs) or possibly an unstable lead.
The Sensing test is performed via the

START

or

INTRINSIC

RHYTHM

button.

Figure 60: Sensing Test Main Screen

«
...
106
107
108
109
110
...
»

Содержание Evia HF











































































































































Отзывы:

Нет отзывов