background image

 

Page 16 

3.3.4 Reaction Archive 

On  this  page,  the  user  can  view  the  entire  reaction  archive.

 

Up  to  fifty  most  recent 

analysis results are listed at a time in the table. The user can: 

  Specify the number of analysis results listed.  

Type  in  the number  of  analysis  results  required  in  the first  text  input  box  and 
then press the 

Submit

 button. 

  List all reactions since a certain date.  

Click  on  the  blue  calendar  icon  beside  the  second  text  input  box. A  calendar 
will appear. Navigate through the calendar and select a date. The second text 
input  box  will  automatically  be  filled  with  the  date  selected.  Click  the 

Submit

 

button. 

  Set the number of items per page using the drop down list. 

Select the analysis results to be displayed in the third text input box and then 
press the 

Submit

 button.  

  Search for reactions based on any number or text. 

Type  in  a  number  or  text  in  the 

Search 

input  box  (the  fourth  text  input  box). 

System  automatically  displays  relevant  analysis  results  containing  the 
searched number or text. 

 

 

 

Содержание Network Control Unit





































Отзывы: