Biotage Isolera Four Скачать руководство пользователя

Страница: 97 / 116

411829-L, Maintenance

April 2012

Page 5-12

7. Pull out the UV lamp and disconnect it from the power cable; see Figure 5-14.

Figure 5-14. Disconnect the UV Lamp

NOTE

Do no touch the UV lamp glass.

8. Mount a new UV lamp (P/N 09830 for all internal Isolera detectors except UV-VIS and P/N

412970 for UV-VIS). Ensure the power cable is positioned so that it does not get in contact with
the fans at the left side of the UV lamp.

9. If using a UV-VIS detector, replace the tungsten lamp (P/N 412970):

a. Loosen the screw holding the tungsten lamp in position using the wrench delivered with

the system.

b. Pull out the tungsten lamp and disconnect it from the power cable; see Figure 5-15.
c. Mount a new tungsten lamp. Ensure the lamp is fully inserted and the power cable is

positioned so that it does not get in contact with the fans at the left side of the UV lamp.

Figure 5-15. Disconnect the Tungsten Lamp

10. When you are done, put the service panel back in place.
11. Reconnect the system and turn it on.
12. When the main menu appears, log into the System mode (see page 3-1).
13. Ensure that the detector flow cell is clean (see page 5-3) and then perform an intensity

calibration:

a. Select the

Maintenance

tab in the right-hand panel.

b. Press

Calibrate

in the

UV Detector

field. Read and follow the instructions that appear on

the screen.

Press here and
disconnect the
UV lamp

Locking screw

Press here
and disconnect
the lamp

Содержание Isolera Four





















































































































Результаты поиска

Содержание Isolera Four

Отзывы:

Похожие инструкции для Isolera Four

Бренды по названию

Популярные бренды

Biotage Isolera Four, Руководство пользователя

Результаты поиска

Содержание Isolera Four

Отзывы:

Похожие инструкции для Isolera Four

Бренды по названию

Популярные бренды