Biostar K8M800 MICRO AM2 Скачать руководство пользователя страница 79

Страница: 79 / 94

K8M800 Micro AM2 BIOS Setup

OnChip USB Controller

This option should be enabled if your system has a USB installed on the system
board. You will need to disable this feature if you add a higher performance
controller.

The Choices: All Enabled

(default), All Disabled, 1&2 USB Port, 2&3 USB

Port, 1&3 USB Port, 1 USB Port, 2 USB Port, 3 USB Port.

Onchip EHCI Controller

This item allows you to enable or disable the onchip EHCI controller.

The Choices: Enabled

(default), Disabled.

USB Emulation Support

This item allows you to enable or disable the USB Keyboard/ Mouse Legacy
Support.

The Choices: On

(default), off, KB/ MS.

USB Keyboard Support

Enables support for USB attached mouse/keyboard.

The Choices: Auto

(default), Enabled.

USB Mouse Support

Enables support for USB attached mouse/keyboard.

The Choices: Disabled

(default), Enabled.

Содержание K8M800 MICRO AM2































































































Результаты поиска

Содержание K8M800 MICRO AM2

Отзывы:

Похожие инструкции для K8M800 MICRO AM2

Бренды по названию

Популярные бренды

Biostar K8M800 MICRO AM2, Руководство пользователя

Результаты поиска

Содержание K8M800 MICRO AM2

Отзывы:

Похожие инструкции для K8M800 MICRO AM2

Бренды по названию

Популярные бренды