background image

 

 

Operation Manual BioSmart PV-WM v.029.1|03.2021|en 

 

Page 18 of 24

 

BioSmart PV-WM Reader  

Operation Manual 

 

Figure 12 

 Readers connection scheme 

 

Checking the Reader's Functionality 

To check the reader operability, put your palm to the palm vein scanner or a card of the corresponding 

format to the card reader (provided that the reader is connected to a powered BioSmart UniPass controller). 

A beep should sound, and the LED should display a successful or unsuccessful identification signal. 

 

Reader Faults and Method of Its Elimination 

Troubleshooting methods for some reader problems are shown in the Table 7. 

Table 7 - Reader faults and methods of their elimination. 

 

Fault description 

Possible reason 

Elimination method 

The reader doesn

turn on 

Insufficient supply voltage

 

Connect to another power supply 

Reader doesn

respond to applied 
palm/card 

Connection with BioSmart 

UniPass controller isn

established 

Restart the BioSmart UniPass 

controller and reader on power 
supply. Make sure the reader and 
controller are powered at the same 

time 

BioSmart UniPas controller 
has a working model not 

providing palm/card waiting 

Check the working model BioSmart 
SmartHub or the BioSmart UniPass 

controller settings 

The user can

t be 

identified by the palm 
veins 

User's palm vein patterns are 

absent in the Biosmart-Studio 
software database 

Check the user templates presence, if 

it’s

 necessary, scan the palm veins 

(see Biosmart-Studio User Guide or 
User Manual BioSmart UniPass 

Controller) 

Содержание PV-WM-MFR

























Отзывы: