BEFORE STARTING YOUR PANEL
HEATER
Please make sure that feet are properly fixed to
each end of the unit (see Fig. 2 and assembly
instruction insert). Alternatively you can wall
mount the unit following the below instructions:
Wall Mounting
IMPORTANT:
Before drilling into any wall
ensure no electrical cables are present in the
area.
NOTE:
Due to the multitude of potential
mounting surfaces, mounting screws are not
included with this product. Please consult a
professional or visit your local hardware store to
determine which type of screw is best for your
particular wall.
1. Remove feet from main unit, if installed.
2. Secure the mounting brackets (Fig. 4B and
3C) to the wall using the dimensions provided
in Fig. 4A.
3. Hang main body on wall brackets installing
first onto bracket “I” , then onto bracket “II”.
(See Fig. 4D & 4E)
SETTING UP - FIRST USE ONLY:
1. Put batteries into remote control by removing
the battery cover located on the reverse side.
Use 3 AAA batteries (Not included) only. DO
NOT mix alkaline and heavy duty batteries.
Do not mix old and new batteries.
WARNING:
Remove batteries before
discarding the remote control.
2. The “ROOM” temperature will be displayed.
3. Plug heater into mains supply. The power light
(Red) will illuminate to signal that the unit is in
stand-by mode.
4. The first time the unit is plugged in, it will
beep every two seconds until it is
synchronised with the remote. To synchronise
the unit with the remote control follow the
steps below:-
• Unlock remote by holding down the “MODE”
button for 2 seconds until the “LOCK” symbol
disappears from the screen. (This must also
be done before each use of the remote).
• Once the remote is unlocked, press the
‘MODE” button again and the unit will quickly
beep 5 times telling the user the signal was
received and the remote is synchronised. In
the event that your remote control does not
communicate- “sync” with your main unit after
reading and following the operating
instructions, please follow the below set up:
•
Hold down both mode button on the
remote control and main unit for 5 seconds
(the power LED will blink once quickly).
•
Release the mode button and the main
unit will begin to beep.
•
Now please follow the above instructions
on how to 'sync' your remote control with
your unit.
•
If you still encounter operational issues
please call: 0800 052 3615
5. In the event that your remote control does
notcommunicate- “sync” with your main unit
after reading and following the operating
instructions. Please follow the below set-up:
• Hold down both mode button on the remote
control and main unit for 5 seconds (the
power LED will blink once quickly).
• Release the mode buttons and the main unit
will begin to beep.
• Now please follow above instructions on how
to 'sync' your remote control with your unit.
USE OF GALILEO
TM
REMOTE CONTROL
• The display can show either Fahrenheit or
Celsius. To change the reading on the remote
control display, unlock the remote, then turn
the remote over and push the button located
on the right hand side, under the stand, with a
ball point pen tip. This switch will change the
reading from ºF to ºC and vice versa.
• Whilst using the remote, the backlight function
will automatically turn on when any button is
pushed and will turn off after 15 seconds of
non-use.
• The maximum transmission distance for the
remote control is 30 ft. (9 Metres). Do not use
or position the remote more than 30 ft (9
Metres) from heater. For accurate temperature
control the remote control must be used in
same room as heater.
• When positioning the remote control, use the
flip up stand on the reverse side.
• Always position the remote control at least 3
ft. (1 Metre) from the heater in a convenient
position away from draughts or anything that
would influence the room temperature
reading. For example, cold window-sill or
under warm lighting.
• Because heat rises and the remote control
senses temperature, the remote control
should not be positioned higher than 4 ft (1.2
Metres) from the floor.
• NEVER place the remote control on the
storage hook on the heater when it is in use.
This will upset the readings and prevent
proper and satisfactory operation. (See Fig. 5)
• The "Room" temperature will always display
on the remote screen if good batteries are in
the remote.
• If the batteries are running low on power, a
low battery indicator will appear on the
remote. Low batteries will effect transmission
distance and the screen contrast. We
recommend replacing batteries immediately.
Do not mix old and new batteries.
• Every minute while in “AUTO” mode, the
remote control communicates with the heater.
If the remote control goes out of range and/or
has low batteries, the communication will
stop, and after 8 minutes of non-
communication, the heater will shut off.
• Do not cover the remote control whilst in use
as this may affect the accuracy of the
temperature reading.
HEATER OPERATION WITH REMOTE
When the heater is plugged into the mains
supply, the power light (Red) will illuminate to
signal that the unit is in stand-by mode.
Manual Operation with remote
1. Press “MODE” button for 2 seconds to unlock
the remote.
2. Press “MODE” button on the remote. The
remote screen will display “ON”. The “ON”
light will illuminate. In this mode, the heater
will operate continuously.
Auto Thermostat Operation with
remote
1. Press “MODE” button for 2 seconds to unlock
the remote.
2. Press “MODE” button on remote until the
remote screen displays “ON” and “AUTO”.
The “Set” temperature is displayed next to the
“Room” temp. The “Auto” light on heater will
illuminate. The heater and “ON” light will cycle
on and off as the unit maintains the “Set”
temperature.
3. To turn heater “Off”, unlock remote, then
press the “MODE” button and the remote
screen display will clear except for the “Room”
temperature and the heater will shut off.
NOTE:
It is normal for the heater to cycle on
and off as it maintains the preset temperature.
To prevent the heater from cycling, you need to
raise the thermostat setting.
ADJUSTING SET TEMPERATURE
1. Press ‘MODE’ button for 2 seconds to unlock
the remote.
2. Increase - When in “AUTO” mode, press the
(+) button on the remote. The “Set” number
will increase with each press. Hold the button
down to scroll. The minimum temp is 13ºC
and the maximum is 26ºC. The remote scrolls
one digit at a time in a continuous loop. 13ºC,
14º...25º, 26º, 13º, 14º....
3. Decrease - When in ‘AUTO’ mode, press the
(-) button on the remote. The “Set” number
will decrease with each press. The minimum
temp is 13ºC and the maximum is 26ºC. The
remote scrolls one digit at a time in a
continuous loop. 13º, 14º...25º, 26º, 13º,
14º....
HEATER OPERATION without remote
When the heater is plugged into the mains
supply, the power light (Red) ( ) will illuminate
to signal that the unit is in stand-by mode.
Remote and heater are OFF:
1. Press the “MODE” button on the heater the
first time. The “ON” light illuminates and the
heater runs continuously.
2. Press the “MODE” button a second time and
the heater shuts off.
NOTE:
The “Auto On” light on the heater only
illuminates when the heater is set to “auto”
mode by the remote.
Remote is ON and Heater is ON:
1. Press the “MODE” button on the heater. The
heater will then switch “Modes”; The heater’s
lights will reflect the change. The remote will
display a different mode - the mode in which it
was set to last. If a button is pressed on the
remote (after unlocking), the remote’s signal
will override the “Mode” on the heater and the
two will be back in sync.
TIMER FUNCTIONS
Using Timer to turn heater off (set
with heater operating)
1. On the remote, hold ‘MODE’ button for 2
seconds to unlock remote.
2. Push (+) and (-) together at once:
• “Timer” and 1Hr appears on the screen.
3. Push (+) and (-) to adjust the number of hours
the heater will run before it automatically
shuts itself off.
• You can choose from:1,2,3,4,5,6,7,8 hours
• 1 through 8 will scroll in a continuous loop
4. After you have made your selection, the
whole screen flashes for 5 times 5 seconds
after last button push of (+) or (-) then goes
back to previous mode. The “Timer” remains
lit to show the timer function has been set.
5. At any time if you unlock the remote and push
the ‘MODE’ button to turn the heater off the
timer setting will be erased and “Timer” will
disappear from the remote.
6. To check how much time is remaining, press
and hold the (+) and (-) buttons
simultaneously.
NOTE:
The remote does not have to be
unlocked to check the time remaining.
Using Timer to turn heater on (set with
heater off)
This function is used to preheat a room by
setting the timer.
3
4
BPH1009IUK06EM1.qxd 8/15/06 3:05 PM Page 7
