GUARANTEE
PLEASE KEEP YOUR RECEIPT AS THIS WILL
BE REQUIRED FOR ANY CLAIMS UNDER
THIS GUARANTEE.
• This product is guaranteed for 3 years.
• In the unlikely event of breakdown, please
take it back to the place of purchase, with
your till receipt and a copy of this guarantee.
• The rights and benefits under this guarantee
are additional to your statutory rights which
are not affected by this guarantee.
• Holmes Products Europe undertakes within
the specific period, to repair or replace free of
charge, any part of the appliance found to be
defective provided that:
• We are promptly informed of the defect.
• The appliance has not been altered in any
way or subjected to misuse or repair by a
person other than a person authorised by
Holmes Products Europe.
• No rights are given under this guarantee to a
person acquiring the appliance second hand
or for commercial or communal uses.
• Any repaired or replaced appliance will be
guaranteed on these terms for the remaining
portion of the guarantee.
We recommend that you send us the attached
guarantee card in order to register your
guarantee with Holmes Products Europe.
THIS PRODUCT IS MANUFACTURED TO
COMPLY WITH THE E.E.C. DIRECTIVES
73/23/EEC, 89/336/EEC AND 98/37/EEC.
Waste electrical products should
not be disposed of with
Household waste. Please
recycle where facilities exist.
Check on the following website
for further recycling and WEEE
information: www.bionaire.com/europe or e-mail
[email protected]
6
to previous mode. The timer will turn the heater on
and run for 2 hours. During the 2 hours, the digital
thermostat will maintain the room in 'auto-high' at
the default of 21ºC (72 ºF).
6. At any time if you unlock the remote and push
the 'MODE' button on the remote, the timer
setting will be erased and 'Timer' will
disappear from the screen.
7. To check how much time is remaining, press
and hold the (+) and (-) buttons simultaneously.
NOTE:
The remote does not have to be
unlocked to check the time remaining.
AUTO SAFETY SHUT OFF
The heater has a built in safety device which will
switch off the heater automatically in case of
accidental overheating. It can only resume
operation when the user has reset the unit.
To reset the heater
1. Unplug the heater and wait for 30 minutes for
the unit to cool down.
2. After the 30 minutes, plug the unit in again
and operate normally.
TIP-OVER INSTRUCTIONS
When the unit is accidentally knocked over, it
will instantly shut off. To reset, simply place the
heater in an upright position and press the
MODE button. It will operate normally.
CLEANING AND MAINTENANCE
• Turn off the unit.
• Remove the plug from the wall socket.
• Wait for the heater to cool down sufficiently.
• You may clean the outside of the heater with
a damp cloth. Do NOT allow water to come
into the appliance. Do NOT use soap or
chemicals, which may damage the housing.
Allow sufficient time to dry before plugging the
unit back in the socket.
• Clean the air inlet and outlet openings
regularly (with normal use at least twice a
year) with a vacuum cleaner.
STORAGE TIPS
If you do not plan to use your heater for an
extended period of time (i.e. during the summer
months), we recommend you to re-pack the unit
in its original packaging or any other dust-free
packaging and store it in a dry and cool place.
FOR U.K. AND IRELAND ONLY:
If the plug is not suitable for the socket outlets in
your home, it can be removed and replaced by
a plug of the correct type. Please refer to
'Installation of a plug' below.
Installation of a plug Applicable to
U.K. and Ireland.
WARNING - THIS APPLIANCE MUST BE
EARTHED
The wires in the mains lead are coloured as such:
GREEN AND YELLOW
- EARTH
BROWN
- LIVE
BLUE -
NEUTRAL
Please note that the colour of these mains wires
may not correspond with the colour markings
that identify the terminals in your plug.
Please proceed as follows:
The wire which is coloured GREEN AND
YELLOW must be connected to the terminal
which is marked with the letter 'E' or by the
earth symbol or coloured GREEN or GREEN
AND YELLOW.
The BROWN coloured wire must be connected
to the terminal, which is marked with the letter
'L' or is coloured RED.
The BLUE coloured wire must be connected to
the terminal, which is marked with the letter 'N'
or is coloured BLACK.
NOTE:
If the terminals in the plug are not
marked or if you are unsure or in doubt about
the installation of the plug please contact a
qualified electrician.
If a 13A 3-pin plug is fitted, it must be an ASTA
approved plug, conforming to BS1363 standard.
Replacement 13A fuses must be BSI or ASTA
BS1362 approved.
5
BCV3100IUK06EM1 revised.qxd 8/10/06 17:19 Page 9
