- 1 -
- 6 -
The SunRise Clock Radio™ is a naturally great way to wake up and fall asleep
every day. That’s because humans are programmed by nature to wake to the
rising sun and sleep when the sun goes down. Waking up to the SunRise Radio
can help you start the day feeling more refreshed and ready to go. Falling asleep
to its simulated sunset can help you relax and get to sleep more easily. Please
take a few moments to familiarize yourself with the control buttons and clock
display to ensure you get off to a good start with your new SunRise Radio. We
recommend reading through and doing the programming before operation.
Setting up the SunRise Radio
For best results, place the clock near your bed on a bedside table close to pillow
level. Plug the clock directly into a wall outlet. Most uninterruptable power
supplies and some surge protectors will not work with the clock. If an extension
cord must be used, it should have 3-prongs and be heavy duty. NOTE: Until the
time has been set, or after a prolonged power outage, the digits on the clock will
flash on and off to let you know the time and other functions need to be set.
Programming the SunRise Radio
Press the PROGRAM (P) button to enter the clock’s menu and change any of
the clock settings. NOTE: The menu is not accessible if the ALARM (
☼
)
button is up (on). The text display below the time digits will show the setting
you are changing and what the current status is. Change the setting using the
PLUS button (+) and MINUS button (-). Once you have completed a setting,
you can press the PROGRAM (P) button again to adjust another setting, or
simply wait for approximately 12 seconds and the clock will exit the menu
automatically and go back to displaying the time. When the lower display reads,
“MORE?” you can exit the menu by pressing the minus button or press the
(P) button to adjust another setting. Holding down the (P) button will exit from
the programming menu.
Setting the Wake-Up Time
When the ALARM (
☼
) button is up, the Alarm Sun symbol (
☼
) shows on the
display and the alarm is on. To adjust the wake up time, make sure the ALARM
(
☼
) button is down (off). Press the PROGRAM (P) button once, so the display
reads “SET ALARM”. Then adjust the alarm time with (+) and (-) buttons
until desired time is set. Holding in the (+) or (-) button will cause the alarm
time to change rapidly.
IMPORTANT SAFETY
INSTRUCTIONS
* This lamp has a polarized plug (one blade is wider than the other) as a safety
feature to reduce the risk of electrical shock. This plug will fit in a polarized
outlet only one way. Any extension cord, if used, should be polarized and
grounded.
* Never remove the glass globe while the lamp is, or has recently been,
operating. The bulb and globe can be extremely hot.
* As with any electrical product, do not immerse the clock/wire in water.
* Never use a bulb with greater than the rated wattage - 60 Watts.
* Do not remove the globe or bulb while the clock is plugged into the wall.
* There are no user serviceable parts. Do not open case for any reason.
Replacing the Bulb
Unplug the clock from the wall. Remove the glass globe from the clock by
pulling upward. Hold the base with one hand, and gently pull up on the glass
globe with the other. Unscrew the bulb. *Caution: If the bulb was recently in
use, it will be hot. Let the lamp cool before removing the bulb. Screw in the
new bulb completely (NEVER use more than a 60W bulb). Carefully put the
globe back on by lowering it over the bulb and making sure it catches on the
latches in the base. Plug in the clock, re-set the time, and re-set your
preferences.
Replacement bulbs are available in most hardware stores or from BioBrite, Inc.
Ask for a 120 Volt 60 Watt frosted bulb with an E12 candelabra base.
Power Outage
The clock memorizes all programming specifications even if the power goes out
or the clock is unplugged. If the power goes out for only a few minutes, you
will not even need to reset the time.
Service
If your Sunrise Radio is not operating properly, please contact BioBrite, Inc.
directly at (301) 961-5940 for customer service and repairs. Please call before
sending anything in for repair—many times the problem can be remedied over
the phone. If repairs are necessary, keep the globe and bulb, secure the plug,
and carefully pack the clock base and send it along with your contact
information and a note explaining the problem to:
BioBrite Service Center
4330 East West Highway, Ste. 310
Bethesda, MD 20814
Display Reference Guide
☼
= ALARM SET symbol
)
)
)
=
BEEP ON symbol
# = RADIO WAKE ON symbol
! = FLASHING ON symbol
PM = PM (after midday) symbol
