1
6
The SunRise Clock is a great way to wake up feeling more refreshed and ready
to go. Humans are naturally adapted to wake to the rising sun and sleep at
sunset. So waking up to a simulated sunrise can give your body a gentle and
natural boost in the morning. Please take a few moments to read the directions
to ensure you get off to a good start with your SunRise Clock.
SETTING UP THE SUNRISE CLOCK
First, insert the light bulb (included) into clock. Then, set the clock near your
bed on a nightstand or bedside table close to pillow level; plug the clock into a
wall outlet; do not use surge protectors, or long extension cords unless they have
3 prongs in the plug and are heavy duty. NOTE: Until time has been set, or after
a prolonged power outage, the digits on the clock will flash on and off.
Before doing anything, you should familiarize yourself with the clock control
buttons. The PROGRAM button (labeled P), is used to change all the settings.
The words below the time display will show you what setting you are changing
and what the current setting is. To adjust any setting, make sure the ALARM
button (A) is pressed IN (off) so that the symbol for the sun is not lit. Press the
PROGRAM button a number of times then, within the next few seconds, change
the setting by pressing the + or – button. After you have programmed all the
settings the way you want them, simply wait for 12 seconds, and the display will
return to the time mode.
Button Reference Guide
P
PROGRAM button. Programs time and other settings.
–
MINUS button. Dims light and changes settings.
+
PLUS button. Brightens light and changes settings.
A
ALARM button. Activates alarm on or off.
NOTE: If the display is too dim to see easily, press the ALARM button IN and
the display will become bright.
IMPORTANT SAFETY
INSTRUCTIONS
•
The clock has a polarized plug (one prong is wider than the other) which
will fit in an outlet only one way. If the plug does not fit in the outlet,
reverse the plug. Most uninterruptable power supplies and some surge
protectors will not work with the clock. If an extension cord must be
used, it should have 3 prongs and be heavy duty. Do not alter the plug.
•
Never remove the glass globe while the lamp is, or has recently been,
operating. The bulb and globe can be extremely hot!
•
As with any electrical product, do not immerse the clock/wire in water.
•
Never use a bulb with greater than 60 Watts maximum.
•
There are no user-serviceable parts. Please do not open the case.
Replacing the Bulb:
Your BioBrite clock uses a standard 60-Watt bulb with a Candelabra (E12) base.
Special bulbs that produce more light are available through BioBrite. To replace
the bulb:
1) Unplug the clock from the wall.
2) Remove the glass globe from the clock by pulling firmly upward. Remove
the globe by holding the base with one hand, and pulling up on the glass
globe with the other hand.
3) Unscrew the bulb. *Caution: If the bulb was recently in use, it will be hot -
let the lamp cool before removing the bulb.
4) Screw in the new bulb completely. Carefully put the globe back on by
lowering over the bulb and making sure it catches on the latches in the base.
5) Plug in the SunRise clock, re-set the time, and re-set your preferences.
Troubleshooting Problem 1: The light will not come on, but the clock works.
Solution: The bulb may be burned out. Look at the bulb and see if the filament
is broken. Replace the bulb and be sure the bulb is fully screwed into the socket.
Troubleshooting Problem 2: Neither the light nor the clock works.
Solution: Unplug the clock from the wall for several seconds and re-plug it in
while holding in the PROGRAM button. Doing this will reset the clock and
restore all the default settings.
Service:
If your SunRise Clock is not operating properly, contact BioBrite directly for
customer service, warranty repairs, and out-of-warranty repairs by e-mail at
or calling (301) 961-5940. Please contact us before sending
anything in because many times problems can be solved by Customer Service.
Display Reference Guide
☼
ALARM SET sun symbol
)
)
)
BEEP ON sound symbol
PM
After midday symbol
#
Sleep Sound on symbol
